Red xj
#121
Thread Starter
CF Veteran
Joined: May 2010
Posts: 1,626
Likes: 1
From: Maryville Tennessee
Year: 1995
Model: Cherokee
Engine: 4.0 L
Just pull the relay and fuse under the hood in the power dist center,and then I just disconnected the wires to the ringtone could have just left em but just wanted to clean up the unused stuff so it was neat
#122
Thread Starter
CF Veteran
Joined: May 2010
Posts: 1,626
Likes: 1
From: Maryville Tennessee
Year: 1995
Model: Cherokee
Engine: 4.0 L
New 33s
Started trimming my fenders for my new 33x12.50 Firestone MTs Friday night,Did the usual cut and fold on the rear pretty happy with it but I am wondering if I trimmed enough on the front fenders.I trimmed off the the first lip that had the factory flare holes,is this enough ya think?4.5'' of lift btw.I put washers in the steering stops so no rubbing when at full turn.Can anybody with a similar lift and tire combo remember how much they cut up on the front?And I have some hockey pucks I plan on using for bump stops.
#125
Senior Member
Joined: Feb 2010
Posts: 938
Likes: 1
From: Alto, MI
Year: 2002
Model: Grand Cherokee
Engine: 4.7
hey man, nice build! I had 33s on a 4.5" lift also. That looks like it will work just fine. If you have to cut anymore, it will be behind the front tires on the bottom part of the fender. I actually ran 35s also down the trails and had no rubbing issues.
#126
Thread Starter
CF Veteran
Joined: May 2010
Posts: 1,626
Likes: 1
From: Maryville Tennessee
Year: 1995
Model: Cherokee
Engine: 4.0 L
Sweet thats good to know,I may go ahead and trim a little more behind the front then.just gotta figure out how to make the angle look right.got any pics of how you did yours?
#127
Senior Member
Joined: Feb 2010
Posts: 938
Likes: 1
From: Alto, MI
Year: 2002
Model: Grand Cherokee
Engine: 4.7
#128
Member
Joined: Dec 2010
Posts: 182
Likes: 0
From: Bozeman, MT
Year: 2000
Model: Cherokee
Engine: 4.0 I-6
I picked up my sliders last night and painted them when I got home.Then I installed them today.Just drilled out the holes where I wanted them on the pinch weld used 5 5/16th bolts w locking washers on each pinch and the main leg that goes to the unibody is 4 3/8th self threaders on each.Very happy with them and for sure will be buying some more stuff from Mayhem.Heres a list of the stuff I used to install,I just copied what another large off road company uses on their sliders.16-3/8 x 2'' self thread screws.10-5/16 x 1 1/4(trim these off after you finish tightening them) 10-5/16 nuts,10-5/16 flat washers and 10 5/16 lock washers.And a 5/16 bit for pilot holes for the self threaders and for the bolts in the pinch.
#129
Senior Member
Joined: Dec 2010
Posts: 686
Likes: 1
From: San Diego
Year: 1999
Model: Cherokee
Engine: 4.0L inline 6
BTW nice build man.
#131
Senior Member
Joined: Dec 2010
Posts: 686
Likes: 1
From: San Diego
Year: 1999
Model: Cherokee
Engine: 4.0L inline 6
Once again.. I'm really enjoying reading your build. Is that front bumper that is being sold on Ebay??
#132
Thread Starter
CF Veteran
Joined: May 2010
Posts: 1,626
Likes: 1
From: Maryville Tennessee
Year: 1995
Model: Cherokee
Engine: 4.0 L
#133
Thread Starter
CF Veteran
Joined: May 2010
Posts: 1,626
Likes: 1
From: Maryville Tennessee
Year: 1995
Model: Cherokee
Engine: 4.0 L
#134
Thread Starter
CF Veteran
Joined: May 2010
Posts: 1,626
Likes: 1
From: Maryville Tennessee
Year: 1995
Model: Cherokee
Engine: 4.0 L
Decided to pull it up on the back deck(thats what their for right?girl friend says its not.)Tires looked a lil too close for comfort in the front, so I trimmed a little bit more...I think it will be fine now,thats as much as I can go without relocating the wind shield washer reservoir or doing some funky angle right behind the rear of the front tires.Should be a little more t flex than in these pics,just to lazy to pull it back up there
Last edited by Skunkape; 02-06-2011 at 04:41 PM.
#135
Thread Starter
CF Veteran
Joined: May 2010
Posts: 1,626
Likes: 1
From: Maryville Tennessee
Year: 1995
Model: Cherokee
Engine: 4.0 L
Got to try out my new 33s and my fender trim job today and wheel with a couple other forum members,Sgtskid and Project Mahyem.Had a blast!
Last edited by Skunkape; 02-12-2011 at 08:47 PM.