Cherokee brake bleed pattern
#1
Member
Thread Starter
Join Date: Sep 2011
Location: Illinois
Posts: 197
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
Cherokee brake bleed pattern
I have a 98 Cherokee se i need to bleed my brakes does any one know the proper pattern? Thanks
#5
Senior Member
Join Date: Oct 2011
Location: Warren, PA 16365
Posts: 763
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L
what the hell, I'll 3rd this and add:
It's easiest if you have someone to pump the brakes 2-3x and hold while you open the valve and close it when he hollers stop when the pedal hits the floor. Then he can top off the reservoir while you roll over to the next brake. Also using a small tube running into a container to catch the fluid from the valve will save you a LOT of clean up.
It's easiest if you have someone to pump the brakes 2-3x and hold while you open the valve and close it when he hollers stop when the pedal hits the floor. Then he can top off the reservoir while you roll over to the next brake. Also using a small tube running into a container to catch the fluid from the valve will save you a LOT of clean up.
#6
CF Veteran
Join Date: Aug 2010
Location: Nashville, TN
Posts: 1,150
Likes: 0
Received 1 Like
on
1 Post
Year: 1997, 1993
Model: Cherokee
Engine: 4.0L
Not to thread jack but that's the way all vehicles should be bled, or so I thought. Are there vehicles out there that have a different bleeding pattern that I'm unaware of?
#7
I have a pressure bleeder tank, and makes this procedure a piece of cake.
Trending Topics
#8
Junior Member
Join Date: Nov 2011
Location: GVRD, B.C. Canada
Posts: 91
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0
My 67 chevy pickup you have to do the driver's side rear, then passenger rear because the main line is run down the passenger side to the T, then splits. Not sure why they crossed the main line just to have it cross back over, but that's where the line holders are on the frame.
#9
Member
Thread Starter
Join Date: Sep 2011
Location: Illinois
Posts: 197
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
okay thanks, i was wondering because i know some cars have different patterns and i want to get as much air out of my brake system as possible
#12
Member
Thread Starter
Join Date: Sep 2011
Location: Illinois
Posts: 197
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
#13
Newbie
Join Date: Sep 2011
Location: Nova Scotia
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
I had a couple Fords that were a nightmare to get the air out of.
Odd pattern and you had to cycle the ABS with "Sun electronic tool #43798x" to get the air out from behind the valves.
Nobody has a "Sun electronic tool #43798x".
This non-ABS Cherokee is a dream. Totally old school!
Heck after having everything apart I gravity bled the brakes in 10 minutes.
Love it.
Steve
#14
Senior Member
Join Date: Dec 2008
Location: Aldergrove,BC,Canada
Posts: 564
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Wagoneer
Engine: 4.0L I6
toyota trucks have a valve on the frame rail that needs to be bled as well, think its called a load valve or something.....i think its purpose is to compensate the for loaded verse unloaded vehicle as it runs a link from frame to axle that changes the valve.....confused the **** outta me and a buddy when we first did his brakes when he got the truck and we couldnt figure out why these brakes wouldnt bleed like normal after 2 bottles.
#15
Junior Member
Join Date: Jan 2013
Location: Phoenix / AZ
Posts: 48
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998
Model: Cherokee
Engine: 4.0L I6 PTE
I hate to drag up an old post but I saw a mushy pedal was referanced above and the bleeding was a remody for that.
What about a hard pedal, my other jeeps/trucks have a softer pedal that can be pressed easily and the truck stops easily.
MY new jeep has new pads all the way around but the pedal is hard to press all the way down and come to full stop, espically if you are going fast to quick stop.
What about a hard pedal, my other jeeps/trucks have a softer pedal that can be pressed easily and the truck stops easily.
MY new jeep has new pads all the way around but the pedal is hard to press all the way down and come to full stop, espically if you are going fast to quick stop.