Coolant draining before head swap
#1
Senior Member
Thread Starter
Join Date: Apr 2012
Location: Ocean, New Jersey
Posts: 578
Likes: 0
Received 4 Likes
on
4 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
Coolant draining before head swap
I'm about to do the infamous head swap on my '00 XJ and would like to know the best way to drain the coolant. Is it just enough to remove the lower radiator hose to drain the coolant? I want to make sure I don't make a big mess when I remove the top hoses from the thermostat after I pull the car into the garage. I also rather not run the car long enough to open the thermostat given the condition of the oil/coolant. Of course I'll do a complete flush after the swap along with changing the hoses, etc. Thanks in advance.
I have everything lined up to dig in first thing in the morning...
I have everything lined up to dig in first thing in the morning...
Last edited by Kalali; 05-26-2012 at 08:04 PM.
#5
Senior Member
Join Date: May 2010
Location: MI 48642
Posts: 882
Likes: 0
Received 1 Like
on
1 Post
Year: 1996
Model: Cherokee
Engine: 4.0
I was under the assumption the opening was lower, letting more of the coolant out. I suppose it would be more work especially if the engine isn't getting pulled.
#6
CF Veteran
Join Date: May 2008
Posts: 3,018
Likes: 0
Received 17 Likes
on
17 Posts
Year: 1988
Model: Cherokee
Engine: AMC242
Why go to all the trouble, unless you're replacing the hoses as well?
Remove the radiator cap, open up the drain plug on the radiator. Easier to catch the coolant that way.
You'll probably still lose a little as you lift the head off, but it won't be enough to cause trouble. This is how I've drained the block when pulling the head, and it's worked well for me so far
Remove the radiator cap, open up the drain plug on the radiator. Easier to catch the coolant that way.
You'll probably still lose a little as you lift the head off, but it won't be enough to cause trouble. This is how I've drained the block when pulling the head, and it's worked well for me so far
#7
Senior Member
Thread Starter
Join Date: Apr 2012
Location: Ocean, New Jersey
Posts: 578
Likes: 0
Received 4 Likes
on
4 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
Either way it looks like its going to be messy. Even removing the lower hose is going to make a big mess...I just need to drive the car about 100 feet to get it into the garage. I don't think overheating will be an issue.
Trending Topics
#8
Senior Member
Thread Starter
Join Date: Apr 2012
Location: Ocean, New Jersey
Posts: 578
Likes: 0
Received 4 Likes
on
4 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
5-90, that's how I prefer to do it to catch the coolant but I could not find the radiator drain plug. The FSM says it is on the left side but I just can't see it....Do I need to remove something to see it, I assume from underneath...
#9
Senior Member
Join Date: May 2010
Location: MI 48642
Posts: 882
Likes: 0
Received 1 Like
on
1 Post
Year: 1996
Model: Cherokee
Engine: 4.0
if the rad is older, you may cause more problems by opening it up anyway. They can break off or leak easier than expected. Just be careful, but it should be on the side of the tank, on the bottom left if you want to use it.
#10
Member
Join Date: Mar 2012
Location: Reno
Posts: 202
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0 I6
I had to take off my entire front grill (8 screws I think), but yours may be different. The draincock was on the passenger side right above the bumper stop.
#14
CF Veteran
Join Date: Dec 2010
Location: Missouri
Posts: 1,246
Likes: 0
Received 1 Like
on
1 Post
Year: 1998
Model: Cherokee
Engine: I6 4.0 L
Originally Posted by BotakBeng
x3
What draincock....they are non accessible on my 99.
#15
Senior Member
Thread Starter
Join Date: Apr 2012
Location: Ocean, New Jersey
Posts: 578
Likes: 0
Received 4 Likes
on
4 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
Most of the disassembly is done. Stopped short of removing the head; too late, too tired and too heavy. Removing the manifolds was a bear but doable. The exhaust manifold is a bit hard to move away from the head, specially in the back. I think I will separate it from the exhaust and take it out. That will give me the option of assembling the head and the manifolds on a bench and install as a unit. May not be a bad idea given the location of all those bolts. But I'll definitely need to get help handling it as a unit - probably weigh 100+ lbs and bulky.
I must say, without this site I would have not even attempted a job like this. I feel like I have a whole army of experts behind me...Thanks.