Cracked exhaust manifold?
#1
Seasoned Member
Thread Starter
Join Date: Apr 2015
Location: Denver, Colorado
Posts: 375
Likes: 0
Received 2 Likes
on
2 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
Cracked exhaust manifold?
So yesterday when changing my thermostat I found a crack in my exhaust manifold. I knew these were prone to cracking and I suspected I had one because I can smell pure exhaust if I walk by the engine bay with the engine running. Can I wait till next spring to replace it? Is there a temporary fix that can last till spring? Should I just not worry about it.
Thanks
Thanks
#4
Senior Member
Join Date: Mar 2014
Location: Eastern Long Island, NY
Posts: 952
Received 55 Likes
on
50 Posts
Year: 1996
Model: Cherokee
Engine: I6 Cyl / 4L
I can't imagine costing much, though the welder would have to be very careful with the fuel line that feeds the fuel rail - maybe use some sort of insulating wool like roxul insulation in between.
Maybe other members who weld can give better advice.
Maybe other members who weld can give better advice.
#5
Senior Member
Join Date: Nov 2011
Location: Tallahassee, FL
Posts: 596
Likes: 0
Received 7 Likes
on
7 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
Yes it is an unusual spot to crack, What it looks like is someone used a pry bar between the exhaust manifold and that bracket (which looks bent up) and cracked the manifold.
I would remove that bracket, clean up the surface real well (no rust) and get someone to weld it, hit up your local jeep club for a member with a welder, or just take it in, should be $20-30 to weld up at a shop. (but hard to put a price on it depending on where you live and competition)
I would remove that bracket, clean up the surface real well (no rust) and get someone to weld it, hit up your local jeep club for a member with a welder, or just take it in, should be $20-30 to weld up at a shop. (but hard to put a price on it depending on where you live and competition)
#7
I'm sure you can get through a couple of winter months as is. I would have suggested someone touch it up with a mig, however, if it's weak (thin) there they may blow it out.
Just replace it when you can.
Just replace it when you can.
Trending Topics
#9
CF Veteran
Join Date: Aug 2010
Location: Canton, MI
Posts: 8,357
Likes: 0
Received 90 Likes
on
74 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Talking to several automotive welding shops they said they refuse to weld thin wall headers because they've had too many come backs because the header cracked around their weld.
To get by until you can replace your header you might try using Blue Magic Xtreme QuickSteel to patch up the hole. Follow the instructions carefully.
Saw it available at O'Reilly Auto Parts.
To get by until you can replace your header you might try using Blue Magic Xtreme QuickSteel to patch up the hole. Follow the instructions carefully.
Saw it available at O'Reilly Auto Parts.
#10
Banned
Join Date: Feb 2014
Location: Florida
Posts: 2,379
Likes: 0
Received 17 Likes
on
16 Posts
Year: 2000
Model: Cherokee(XJ)
Engine: Golen 4.6L
As for leaving it alone until spring, I wouldn't. Unless you can find some way to temporarily seal it off so that cold air isn't backing up in there in the winter, I would go ahead and replace it. Is your reluctance to replace it a money thing or a time thing? If it's money, just go get a cheap stock manifold from the junk yard to get you through until you can afford to replace the header. Pull a Part sells them for less than $30.
#11
Seasoned Member
Thread Starter
Join Date: Apr 2015
Location: Denver, Colorado
Posts: 375
Likes: 0
Received 2 Likes
on
2 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
It's a money and time thing. I'm a high schooler with limited funds. My parents are reluctant to keep on dumping money into this thing for the moment. I guess I could throw a junk yard header on but I'm not sure my dad would let me. I also don't know if I could find the time to pull the intake and all the stuff on it off and put it all back on. I'll ask my local exhaust shop to see what they think anyway.
Also could this cause bad MPG? I drive my Jeep like its a mustang but I think I should be getting over 10-12 MPG mixed.
Also could this cause bad MPG? I drive my Jeep like its a mustang but I think I should be getting over 10-12 MPG mixed.
Last edited by jpmarine6786; 11-10-2015 at 11:34 AM.
#12
CF Veteran
Join Date: May 2012
Location: Lost in the wilds of Virginia
Posts: 7,964
Received 957 Likes
on
772 Posts
Year: 1998 Classic (I'll get it running soon....) and 02 Grand
Model: Cherokee (XJ)
Engine: 4.0
Possibly. If air is getting IN (during the off-cycle for that cylinder) it couild be making the O2 sensor report a lean condition, which would cause the PCM to dump fuel.
I suggest you try Ken's remedy. It will only cost a couple of bucks to try, and if it works, you are home free. Make sure you clean that area VERY well, and more than you think you need to. Wire brush then sandpaper. You want the metal shiny bright and rough.
If it doesn't work, well, it was only a few bucks to try it, and it can be cleaned off well enough for welding.
Another possibility: High school welding class? Maybe a free learning project? No welding class there? Try a local junior college. The worst they can do is laugh at you and call a press conference to mock you, right?
#13
Senior Member
Join Date: Sep 2008
Location: Sioux Falls, SD
Posts: 897
Likes: 0
Received 12 Likes
on
9 Posts
Year: 1999
Model: Cherokee(XJ)
Engine: 4.0L
Braze or weld. Absolutely NO Epoxy/Glue/JB Weld/MarineTex etc will work there. ever. It will melt off.
Id brush it, and braze it with some MAPP and silver rod. Would seal up enough till you get around to a new manifold.
Id brush it, and braze it with some MAPP and silver rod. Would seal up enough till you get around to a new manifold.