Front Drive Shaft U Joint Bolt Help
#1
Senior Member
Thread Starter
Join Date: Apr 2010
Location: Marshall, WI
Posts: 720
Likes: 0
Received 1 Like
on
1 Post
Year: 1994
Model: Cherokee
Engine: 4.0L i6
Front Drive Shaft U Joint Bolt Help
So the jackass that last tightened the bolts down for the front drive shaft u joints put them on so freaking tight, they are now stripped. As I dont have a welder to tac weld a nut to the top of the bolt to remove that way, what are some other options i can try? TC is on the work bench so access isnt an issue. Any help would be appreciated.
#2
CF Veteran
Join Date: Aug 2011
Location: Nor-Cal Coast
Posts: 10,489
Likes: 0
Received 18 Likes
on
18 Posts
Year: 90,84
Model: Cherokee
Engine: 4.0,2.5
A pic would be nice. You try a six point? Can you hacksaw the "U" bolt? (or angle grinder). Sometimes a chisel works to turn a POS bolt. Never tried it on something that small though. Heat can make a huge difference, got a propane torch?
#3
Senior Member
Thread Starter
Join Date: Apr 2010
Location: Marshall, WI
Posts: 720
Likes: 0
Received 1 Like
on
1 Post
Year: 1994
Model: Cherokee
Engine: 4.0L i6
its the bolts that hold the clamps down over the ujoint on the TC itself. I was able to get it the clips and ujoint off the front axle no prob, just cant get the drive shaft off the TC now cuz 3 bolt heads are stripped.
I will try the 6 point and see if that works, no torch. I was thinking of maybe i could hammer on a smaller size end wrench and see if that could grip it enough to turn.
I will try the 6 point and see if that works, no torch. I was thinking of maybe i could hammer on a smaller size end wrench and see if that could grip it enough to turn.
#4
CF Veteran
Join Date: Jan 2010
Location: Virginia Beach by way of Michigan
Posts: 5,482
Likes: 0
Received 25 Likes
on
25 Posts
a 6 point will slip easier than a 12 point. One way is to file down a flat spot and use vice grips if it's stripped really bad. PB blast the crud out of it to loosen it as much as possible.
#7
Member
Join Date: Oct 2010
Location: Liberal, Kansas
Posts: 163
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0L
I was in this same situation with my fron driveshaft and my 12 point wrench rounded it. But after I switched to a 6 point it held just fine.
Trending Topics
#8
CF Veteran
Join Date: Aug 2011
Location: Nor-Cal Coast
Posts: 10,489
Likes: 0
Received 18 Likes
on
18 Posts
Year: 90,84
Model: Cherokee
Engine: 4.0,2.5
Guess it depends sometimes nordplz. 6 point needs to move more metal deeper to strip than a 12 point. Less airspace there I guess.
"hammer on a smaller size end wrench" Worth a try. The hammering might help free it.
"hammer on a smaller size end wrench" Worth a try. The hammering might help free it.
Last edited by DFlintstone; 10-13-2011 at 06:22 PM.
#11
Senior Member
Thread Starter
Join Date: Apr 2010
Location: Marshall, WI
Posts: 720
Likes: 0
Received 1 Like
on
1 Post
Year: 1994
Model: Cherokee
Engine: 4.0L i6
Well I got em off. Went down to Harbor Freight and picked up one of those $10 mini torches. Got home, heated up the bolts with the mini torch, grabbed my needle nose vice grips, and surprisingly they broke loose with ease. Went down to the local junk yard and pulled out some new bolts. So good to roll now!
#12
CF Veteran
Join Date: Aug 2011
Location: Nor-Cal Coast
Posts: 10,489
Likes: 0
Received 18 Likes
on
18 Posts
Year: 90,84
Model: Cherokee
Engine: 4.0,2.5
Good for you, mannn that should have been easy. Well done. And now you have a torch
.................................................. .................V..X2, I like the copper anti-seize V
.................................................. .................V..X2, I like the copper anti-seize V
Last edited by DFlintstone; 10-17-2011 at 09:44 PM.
#13
CF Veteran
hope you learned to use anti-seize on the new bolts when you put them in.
i put that **** on everything.
i put that **** on everything.
#15
Senior Member
Join Date: Aug 2010
Location: NC/SC
Posts: 1,012
Likes: 0
Received 1 Like
on
1 Post
Year: 1990
Model: Cherokee
Engine: 4.0
Depending on your axle yoke style Id suggest you drill out the threading and using a ford Ubolt style u-joint retainer. Makes removing it easier and those things ARE BEEF compared to the factory sorry **** straps. Also if you insist on using the factory straps, I suggest you get new bolts. I cant tell you howmany times Ive broken mines on a trail and had to retap the hole....
Link to u-bolt swap
https://www.cherokeeforum.com/f51/re...version-28141/
Link to u-bolt swap
https://www.cherokeeforum.com/f51/re...version-28141/
Last edited by sam24th; 10-18-2011 at 08:12 AM.