Leaf Springs Sagging
#1
Newbie
Thread Starter
Join Date: Apr 2015
Location: Dixie
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
Engine: 4.0L
Leaf Springs Sagging
Okay, so I've been under my 88 xj disconnecting everything getting ready to pull the motor and tranny.
It has always looked a little saggy in the back. My son pointed out the rear leaf springs to me and they look terrible. They are bent the wrong way - completely collapsed.
They are frowny faces - not smiley faces! I know, I know. I shouldn't use such technical jargon.
So where would you begin if you were on a TIGHT budget and needed to repair these rear springs?
Thanks,
Jeff
It has always looked a little saggy in the back. My son pointed out the rear leaf springs to me and they look terrible. They are bent the wrong way - completely collapsed.
They are frowny faces - not smiley faces! I know, I know. I shouldn't use such technical jargon.
So where would you begin if you were on a TIGHT budget and needed to repair these rear springs?
Thanks,
Jeff
#2
Member
Join Date: Feb 2015
Location: Traverse City, MI
Posts: 243
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
I picked up the Dorman springs off Amazon for about $100 a piece. Threw them on and wound up about an inch over stock. They've settled about a half inch. Solid HD springs, but not to firm. Decent ride for such an affordable option. The other nice thing about the Dormans was the bushings were already pressed in to the springs... on some of the replacement springs, you've got to buy the bushings separate and press them in yourself.
#4
Newbie
Thread Starter
Join Date: Apr 2015
Location: Dixie
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
Engine: 4.0L
Thanks Jay,
That's a good point. I'm in Southeast.
So probably won't swing by to pick them up later this afternoon.
Thanks for the feedback,
Jeff
That's a good point. I'm in Southeast.
So probably won't swing by to pick them up later this afternoon.
Thanks for the feedback,
Jeff
#6
CF Veteran
Join Date: Dec 2011
Location: IE (SoCal)
Posts: 1,080
Likes: 0
Received 6 Likes
on
5 Posts
Year: 1994 SE
Model: Cherokee
Engine: 4.0
Darn, guess I'll keep them then.
But seriously, post in the wanted section (not sure if you need to up your post count first?), since springs are usually taken off for a lift, you could probably score some for free or cheap. Cruise craigslist for part outs? Jeep dismantler local? Maybe the regional section here?
But seriously, post in the wanted section (not sure if you need to up your post count first?), since springs are usually taken off for a lift, you could probably score some for free or cheap. Cruise craigslist for part outs? Jeep dismantler local? Maybe the regional section here?
#7
Seasoned Member
Join Date: Aug 2015
Location: New Jersey
Posts: 404
Likes: 0
Received 17 Likes
on
14 Posts
Year: 2000
Model: Cherokee
Engine: 4.0L
I picked up the Dorman springs off Amazon for about $100 a piece. Threw them on and wound up about an inch over stock. They've settled about a half inch. Solid HD springs, but not to firm. Decent ride for such an affordable option. The other nice thing about the Dormans was the bushings were already pressed in to the springs... on some of the replacement springs, you've got to buy the bushings separate and press them in yourself.
Trending Topics
#8
Member
Join Date: Feb 2015
Location: Traverse City, MI
Posts: 243
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
I like them enough that I'll be getting the same ones to put on my 1990 XJ. I'm sure there are bette rones out there, but for the price, I'm extremely happy with them so far. Only been on about 10 months, but no complaints yet.
#10
Senior Member
Join Date: Sep 2008
Location: Sioux Falls, SD
Posts: 897
Likes: 0
Received 12 Likes
on
9 Posts
Year: 1999
Model: Cherokee(XJ)
Engine: 4.0L
I avoided the whole "Remove the main bolts" fiaso and just added a leaf from a 90s GMC Sonoma. S10 leafs will work also.
Look up "Leaf Spring Bastard Pack". By the time you get the new u-bolts and such, the cost should be less than new OEM springs with none of the frame-cutting shenanigans that you need to do to remove the entire spring.
I did mine and used the main spring from then Sonoma with the eyes cut off, and one or 2 of the other from the GMC.
You will need new center pin bolts, some C-Clamps to hold everything together as you are working. A few ratchet straps to horse the axle tube around as you do each side is helpful also.
Just my .02.
Look up "Leaf Spring Bastard Pack". By the time you get the new u-bolts and such, the cost should be less than new OEM springs with none of the frame-cutting shenanigans that you need to do to remove the entire spring.
I did mine and used the main spring from then Sonoma with the eyes cut off, and one or 2 of the other from the GMC.
You will need new center pin bolts, some C-Clamps to hold everything together as you are working. A few ratchet straps to horse the axle tube around as you do each side is helpful also.
Just my .02.
#12
Member
Join Date: Feb 2015
Location: Traverse City, MI
Posts: 243
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
I avoided the whole "Remove the main bolts" fiaso and just added a leaf from a 90s GMC Sonoma. S10 leafs will work also.
Look up "Leaf Spring Bastard Pack". By the time you get the new u-bolts and such, the cost should be less than new OEM springs with none of the frame-cutting shenanigans that you need to do to remove the entire spring.
I did mine and used the main spring from then Sonoma with the eyes cut off, and one or 2 of the other from the GMC.
You will need new center pin bolts, some C-Clamps to hold everything together as you are working. A few ratchet straps to horse the axle tube around as you do each side is helpful also.
Just my .02.
Look up "Leaf Spring Bastard Pack". By the time you get the new u-bolts and such, the cost should be less than new OEM springs with none of the frame-cutting shenanigans that you need to do to remove the entire spring.
I did mine and used the main spring from then Sonoma with the eyes cut off, and one or 2 of the other from the GMC.
You will need new center pin bolts, some C-Clamps to hold everything together as you are working. A few ratchet straps to horse the axle tube around as you do each side is helpful also.
Just my .02.