no injector pulse
#1
Junior Member
Thread Starter
Join Date: Jan 2013
Location: Gardnerville Nv.
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
no injector pulse
Alright i brought home an 88 larado last night no pulse no power at all to the injectors iv replaced the cps the ignition switch iv reniewed the c101changed the ecu i have fuel pressure new pump new filter im at a loss and need it running asap as my winter jeep currently has no axle.
#2
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,971
Received 1,559 Likes
on
1,263 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
Have you tested the CPS output even though it's new?
Did you "tweak" the connectors in the C101?
Did you "tweak" the connectors in the C101?
#3
Junior Member
Thread Starter
Join Date: Jan 2013
Location: Gardnerville Nv.
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
i have no way to test it but i have several new in box and iv tried two of them, could that cause my injectors to not pulse? how can i test it without a dvom?
#4
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,971
Received 1,559 Likes
on
1,263 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
Go here and get this.
http://www.harborfreight.com/7-funct...ter-98025.html
When you get home, read this:
http://learn.adafruit.com/multimeters/
http://www.harborfreight.com/7-funct...ter-98025.html
When you get home, read this:
http://learn.adafruit.com/multimeters/
#5
Injectors have continious voltage but will not open untill the PCM completes the ground path.
Check the PCM ground and associated ground wires before throwing more money at your rig.
Also try swapping the ASD relay with a known good relay in your PCM.
Checked/cleaned your NSS yet?
Check the PCM ground and associated ground wires before throwing more money at your rig.
Also try swapping the ASD relay with a known good relay in your PCM.
Checked/cleaned your NSS yet?
Trending Topics
#10
Junior Member
Thread Starter
Join Date: Jan 2013
Location: Gardnerville Nv.
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
alright so where do i go from here then? i was told there are four grounds from my block to the frame but i only have three grounds. could that do it? it was running just fine then the fuel pump stopped getting power i ran a switch to it and about a week later the injectors just stopped
#11
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,971
Received 1,559 Likes
on
1,263 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
#12
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,971
Received 1,559 Likes
on
1,263 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
alright so where do i go from here then? i was told there are four grounds from my block to the frame but i only have three grounds. could that do it? it was running just fine then the fuel pump stopped getting power i ran a switch to it and about a week later the injectors just stopped
#13
Junior Member
Thread Starter
Join Date: Jan 2013
Location: Gardnerville Nv.
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
Thanks cruiser but iv already tried i use all your tips as soon as i pick up a jeep as it usually solves all problems.
UPDATE: i pulled down the steering coloum as its broken at the tilt the ignition switch was fried so i replaced now the jeep wont even try to turn over however still getting power to everything but my injectors.
UPDATE: i pulled down the steering coloum as its broken at the tilt the ignition switch was fried so i replaced now the jeep wont even try to turn over however still getting power to everything but my injectors.
#14
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,971
Received 1,559 Likes
on
1,263 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
That switch is adjustable on the column by sliding it up or down.
#15
Junior Member
Thread Starter
Join Date: Jan 2013
Location: Gardnerville Nv.
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
sliding the switch didnt make a diffrence i even pulled it back out and tried using a screw driver still nothing im at such a loss with this jeep.