Last edit by: IB Advertising
See related guides and technical advice from our community experts:
Browse all: Engine Guides
- Jeep Cherokee XJ 1984 to 1996 How to Repair Oil Filter Adapter Leak
Step by step instructions for do-it-yourself repairs
Browse all: Engine Guides
Oil Filter Adapter fix
#1
Newbie
Thread Starter
Join Date: Sep 2008
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Cherokee
Engine: 4.0
Oil Filter Adapter fix
My jeep had an oil leak at the oil filter housing, it was the o-ring behind the adapter. I started working on this knowing that it was going to be a dirty job, but i must say i was surprised with just how much trouble it gave me. I will say i probably wouldn't have gotten it done without the much needed help from my brother. I have a 94' XJ so it used the T60 torx bit to remove the housing, on older models ive heard that it just takes a wrench.
To begin you need to drain your engine oil, remove the oil filter and let it sit open for a few minutes to let everything get dry. There's not much space by the housing because it is sitting almost even with the framerail, so i removed the back motor mount bolt (just 1) to get enough room for the bit to fit in there. Now, when i tried to break the bolt holding the housing i ran into alot of trouble. You cant apply heat to this area, its kinda easy to figure out why, so its pretty much all muscle. I broke 2 wrenches, pried with a cheater bar, and finally just got a lil redneck and tied a come-along to the wrench a winched it till it broke. After you do get this loose you may have to work the bolt a small amount by hand because like i said, there's not much of any room to work. The housing pretty much just slides right off, and to replace the o-ring you just clean the housing out and slide it right in place of the old one. To reinstall, just put everything back together exactly the way it came off. My work time was about 4 hours, but that was due to frustrastion of a frozen bolt. I would say if all went well you could do it in about an hour or a little more.
To begin you need to drain your engine oil, remove the oil filter and let it sit open for a few minutes to let everything get dry. There's not much space by the housing because it is sitting almost even with the framerail, so i removed the back motor mount bolt (just 1) to get enough room for the bit to fit in there. Now, when i tried to break the bolt holding the housing i ran into alot of trouble. You cant apply heat to this area, its kinda easy to figure out why, so its pretty much all muscle. I broke 2 wrenches, pried with a cheater bar, and finally just got a lil redneck and tied a come-along to the wrench a winched it till it broke. After you do get this loose you may have to work the bolt a small amount by hand because like i said, there's not much of any room to work. The housing pretty much just slides right off, and to replace the o-ring you just clean the housing out and slide it right in place of the old one. To reinstall, just put everything back together exactly the way it came off. My work time was about 4 hours, but that was due to frustrastion of a frozen bolt. I would say if all went well you could do it in about an hour or a little more.
#4
Renix Super Guru
Join Date: Mar 2008
Location: In yourz postez fissin jurr spelinzs
Posts: 24,653
Likes: 0
Received 19 Likes
on
13 Posts
Year: 1990XJ/1989MJ
Model: Comanche
Engine: 4.0L Renix
extex it takes a T-60 Torx socket to get the bolt loose. I used a socket and vice grips on the socket to break mine loose but turp seems to have had more difficulty than I did.
#5
Newbie
Join Date: Oct 2008
Posts: 3
Likes: 0
Received 1 Like
on
1 Post
Year: 1994
Model: Cherokee
Engine: 4.0L
Tight fit on my 94
I had the same trouble removing the housing but even worse luck putting it back because of the limited clearance. Long story short, I ended up using a socket cap and ratcheting wrench to get the threads to take. Just hoping this might help someone else.
Pic1 Pic2 Pic3 Pic4
Pic1 Pic2 Pic3 Pic4
The following users liked this post:
quititman (02-09-2022)
#6
Newbie
Join Date: Sep 2008
Posts: 27
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: I6 4.0L
Hey guys I'm new to Jeeps and after giving mine a once over this weekend I think I have this same common leak. I was going to perform the fix but just wanted to double check, is there only one o-ring I am supposed to replace? I went to AZ and they said it is just one and from the pictures it looks like just one, but in the technical articles it said there were 3 o-rings and one is only available at the dealer. Was that article describing an older model Cherokee with 3-o-rings because my oil filter set up looks like the one in your pictures.
Thanks for the info too by the way.
Thanks for the info too by the way.
#7
Member
Join Date: Aug 2008
Location: Charlotte, NC (UNCC)/Arcadia, NC
Posts: 199
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Do your self a favor, and go to the dealer and get the o-ring kit. It will come with all 3 that you need (the main o-ring behind the adapter, and the two that are on the bolt holding the adapter in). When I bought the kit from the dealer last year it cost me about $3 and some change. Make sure you get the kit, as they do sell just the main o-ring.
I didn't drain the engine oil as mentioned above....all you need to do is spin the filter off, take the adapter off (the fun part!), then reverse for install. Don't forget to top off the engine oil when you put a new filter back on!
I didn't drain the engine oil as mentioned above....all you need to do is spin the filter off, take the adapter off (the fun part!), then reverse for install. Don't forget to top off the engine oil when you put a new filter back on!
Trending Topics
#8
Renix Super Guru
Join Date: Mar 2008
Location: In yourz postez fissin jurr spelinzs
Posts: 24,653
Likes: 0
Received 19 Likes
on
13 Posts
Year: 1990XJ/1989MJ
Model: Comanche
Engine: 4.0L Renix
4720363 is the dealer part number for the o-ring kit. It does have 3 o rings and if you have never done one you should read up on the procedure before atempting it. If you have an older Jeep with an inverted filter you may want to upgrade to the larger horizontal filter set up. Read MadXJs article HERE He has several good technical articles worth bookmarking.
The following users liked this post:
quititman (02-09-2022)
#10
CF Veteran
Join Date: Jul 2008
Location: Schnecksville, PA
Posts: 1,217
Likes: 0
Received 7 Likes
on
7 Posts
Year: 94 XJ
Model: Cherokee
Engine: 4.0L
4720363 is the dealer part number for the o-ring kit. It does have 3 o rings and if you have never done one you should read up on the procedure before atempting it. If you have an older Jeep with an inverted filter you may want to upgrade to the larger horizontal filter set up. Read MadXJs article HERE He has several good technical articles worth bookmarking.
Our 91 Laredo has the vertical adapter and Lil Red has the horizontal adapter BUT they use the SAME filter. -->>They both have a yellow sticker on firewall warning about the filter thread diameter.
Am I missing something. You say the horizontal is a larger filter??
#11
Seasoned Member
Join Date: Feb 2009
Posts: 358
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0
Anyone looking to this Thread for help might get surprised that T60 torx might not get the job done. I have a 93 4.0 with a stock horizontal oil filter position. I found with the help of FarmFuel that I needed a 9/16 allen key. Good luck.
#13
Senior Member
Join Date: Jul 2008
Location: West Virginia
Posts: 709
Likes: 0
Received 0 Likes
on
0 Posts
Year: 98
Model: Cherokee
Engine: 4.0L
My 98 xj 4.0L doesn't have the oil filter adapater the filter screws directly on to the engine block.I have never saw any other 4.0 with the oil filter mounted this way it makes oil change easy.
#15
Senior Member
Join Date: Dec 2008
Location: northwest Indiana USA
Posts: 606
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990 laredo
Model: Cherokee
i just picked up felpro part # 70301, which says oil adapter o-ring, jeep 6, 242 engine, 1971-90. there is one big o-ring in the package.
will I need other orings too or no on my renix engine? I like having all the parts up front.
will I need other orings too or no on my renix engine? I like having all the parts up front.