Oil pressure gauge pegged out
#1
Newbie
Thread Starter
Join Date: Dec 2018
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee (XJ)
Oil pressure gauge pegged out
Hello everyone, I have a 1988 jeep wagoneer limited and I'm having an issue with my oil pressure gauge. The emissions testing facility wont even take it in if the gauge isnt working, which I kinda think is dumb since the gauge hasn't been working properly in a very long time and they've tested it before. But I'm trying to get the issue resolved and I'm getting nowhere. I've already replaced the oil pressure sending switch, and the gauge. When I replaced the switch, the gauge didn't move, it just stayed past 80 where it's been for a long time. When I replaced the gauge, the gauge was sitting somewhere around 20 before i turned the ignition on, then when i did turn on the accessory, the new gauge pegged out past 80 just like the old one did. There wasn't a change when the car was started either. Is there something else I'm missing? Any help is appreciated. I just haven't been able to find anything on this for anything older than a 1996 xj
#2
Member
Join Date: Oct 2018
Location: Southeast PA
Posts: 118
Likes: 0
Received 24 Likes
on
22 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0
I had the opposite issue:
https://www.cherokeeforum.com/f2/oil...gnosis-247764/
Turned out to be the sender. The system on my 96 sport works by grounding the sender. If you ground the wire to the sender, pressure gauge goes to past 80. Unplug it and it should go to 0. I would try unplugging it and see if you get 0. If not, I suspect you are grounding out before the sender. If you do get 0, it is probably your sender. Make sure you get the right one. MOPAR, not the cheap one (if it is the sender, don't just waste your money if you don't need one).
And not passing inspection is bogus. I'd go somewhere else if I were you.
https://www.cherokeeforum.com/f2/oil...gnosis-247764/
Turned out to be the sender. The system on my 96 sport works by grounding the sender. If you ground the wire to the sender, pressure gauge goes to past 80. Unplug it and it should go to 0. I would try unplugging it and see if you get 0. If not, I suspect you are grounding out before the sender. If you do get 0, it is probably your sender. Make sure you get the right one. MOPAR, not the cheap one (if it is the sender, don't just waste your money if you don't need one).
And not passing inspection is bogus. I'd go somewhere else if I were you.
#3
Newbie
Thread Starter
Join Date: Dec 2018
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee (XJ)
Unfortunately with colorado emissions, I have to go to my county's emissions center and cant take it anywhere else. But I'll try what you've said and see if there are any changes. The gauge is hanging around the 80 mark right now but hasn't moved
#5
Newbie
Thread Starter
Join Date: Dec 2018
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee (XJ)
I already have replaced it. But the problem could be the replacement part was from autozone and not a mopar product. The sender only has one wire, so I wouldn't be able to try the ground fix that was recommended right?
#6
CF Veteran
It works by grounding the gauge and metering the voltage with a small rheostat inside it. You might have another ground you shouldn't have in the printed circuit on the back of the instrument cluster. Or, as you say, cheap chinese stuff. It has been known to happen all too frequently
Trending Topics
#8
Seasoned Member
Join Date: Jul 2013
Location: PA
Posts: 488
Received 92 Likes
on
66 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
I had the same issue last year with mine, and replaced the sending unit and it has been fine since then. It sounds like you have a bad (new) sending unit. Admittedly, I replaced mine with a NAPA one so far so good. I can't bring myself to spend dealer money on 20 year old vehicle. At least not as my first stop for a replacement part.
#9
CF Veteran
Join Date: Oct 2018
Location: Hunt County Texas
Posts: 1,096
Received 166 Likes
on
140 Posts
Year: 1995
Model: Cherokee (XJ)
Engine: 4.0L
Make sure you get the sending unit and NOT the switch. Some parts monkeys dont know the difference
the switch is for the idiot light gauge clusters and will make the gauge peg out
the switch is for the idiot light gauge clusters and will make the gauge peg out
#10
Newbie
Thread Starter
Join Date: Dec 2018
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee (XJ)
Isnt the sending unit also the switch on my xj? Any time I look up the part, no matter the wording, it always comes up with the exact same thing. The part I'm thinking of is located almost right next to the oil filter and kinda looks like a fuel filter with one wire prong coming off of it. Is there another part that's apart of this? Cuz I dont think my cluster even has a light on it for the oil pressure
#11
Senior Member
Join Date: Nov 2012
Location: Harrisburg, Pennsylvania
Posts: 918
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1995
Model: Cherokee
Engine: 4.0L HO
Isnt the sending unit also the switch on my xj? Any time I look up the part, no matter the wording, it always comes up with the exact same thing. The part I'm thinking of is located almost right next to the oil filter and kinda looks like a fuel filter with one wire prong coming off of it. Is there another part that's apart of this? Cuz I dont think my cluster even has a light on it for the oil pressure
#12
Senior Member
There are two instrument cluster options, one with gauges, and one with idiot lights. There are also two different sending units, one that acts as a switch to activate the light, and one that has a resistor to control the gauge. When I switched my cluster in my Jeep that came with idiot lights, the gauge pegged past 80. When I put the proper sending unit in, it works as a normal gauge. I used the Standard brand part, part# PS257. ($20.00 on amazon) No problem so far. I think it was like a 21mm deep socket to change it, but don't quote me on it.
#13
Newbie
Thread Starter
Join Date: Dec 2018
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee (XJ)
Red1992xj, is the jeep you're talking about the same as your username? Aren't there a lot of electrical differences between 90's xj's and the late 80's xj's? I've been finding a lot of information on this problem with xj's that have a completely different "sensor" than mine does. Mine looks like the picture I attached
#14
Senior Member
My apologies, I thought the sensors would be interchangeable. I did a little research on Rockauto, you would probably get the WVE/AIRTEX/WELLS 1S6563 sender. When you look at the listings, it will say either "light" or "gauge". You want the one with the gauge, obviously. If you go to a local part store, check their website first for an exact part#. New guys behind the counter wont give a hoot what they give you. I don't know what the mopar part would run you, but it'd probably be expensive, if you could still get it.
#15
CF Veteran
Join Date: Oct 2018
Location: United Kingdom
Posts: 1,577
Received 278 Likes
on
242 Posts
Year: 1995 RHD
Model: Cherokee (XJ)
Engine: 4.0l
My suggestion is:
- Get a multimeter out and
- Check power to the wire that goes to the sender. From what you said about the new gauge going from 20 - 80 this should be fine. You should see around battery voltage at the wire
- Make up/connect a short lead to connect to the sensor for ease of reading
- Check the resistance of the sensor itself so one probe on earth and one on the short lead. Take note of the reading
- Start the engine and take another reading, this should be different to the previous
- If possible get someone to rev the engine up and down and the reading should move with the RPMs