Overvoltage at RPM
#1
Newbie
Thread Starter
Join Date: Nov 2014
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
Overvoltage at RPM
I am having a problem with my '96 Cherokee. When my RPMs rise to 3000 or higher, my Cherokee's electrical system rises to ~18-19V. When I drop RPM, the voltage drops back to normal operating voltage. I know it is not a bad gauge reading because when it goes into over-voltage condition, the A/C blower fans turn into jet engines and the light behind the gauge cluster turns into a spotlight.
So far, I have cleaned both battery terminal posts. Cleaned the positive battery cable terminal and replaced the ground terminal. I also checked all ground and alternator cables to ensure they are snug. Where should I go from here for troubleshooting?
So far, I have cleaned both battery terminal posts. Cleaned the positive battery cable terminal and replaced the ground terminal. I also checked all ground and alternator cables to ensure they are snug. Where should I go from here for troubleshooting?
#5
CF Veteran
Join Date: May 2012
Location: Lost in the wilds of Virginia
Posts: 7,964
Received 956 Likes
on
771 Posts
Year: 1998 Classic (I'll get it running soon....) and 02 Grand
Model: Cherokee (XJ)
Engine: 4.0
Yep. Start here. It probably needs to be done anyway.
And save yourself some money. Get custom battery cables made by www.bestboatwire.com. Go 4 gauge on the main battery cables and 6 gauge on the secondaries (ground to body and positive to PDC). It's a nice upgrade from factory without being ridiculous (like using 1 gauge). I like getting the clear heat shrink on the ends so that I can see if corrosion ever gets started.
Then go to Amazon for military battery terminal connectors.
I just did this on mine and it is NICE. Easy project, too. Much cheaper than the guys here who sell kits, too. Nothing against them, but $$ is $$.
#7
Caracticus Potts The Mod
Always good to upgrade cables and terminals, but have the alternator tested with the proper equipment....I'm sure you will find the internal regulator is failing.
Have the battery tested as well, after all they work together as a team.
Have the battery tested as well, after all they work together as a team.
Trending Topics
#8
Senior Member
Join Date: Sep 2014
Location: U.P. MI
Posts: 560
Likes: 0
Received 17 Likes
on
16 Posts
Year: 1989
Model: Cherokee
Engine: 4.0L
I believe the voltage regulator on that year is on the PCM. If it turns out to be the issue the only way to fix it is to replace the PCM or install an external, aftermarket voltage regulator.
#12
CF Veteran
Probably not a bad ECU/Voltage Regulator, but instead the ECU "thinks" the system voltage is lower than it should be so it is allowing more system voltage than it should. This probably goes back to bad connections, bad grounds, bad cables, clamps, corrosion.
#14
Newbie
Thread Starter
Join Date: Nov 2014
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
I have the cables on order, but while waiting I've been checking out some more stuff.
I did some checks for continuity with ground on the field wires. I disconnected the wires from the back of the alternator and also unplugged them from the ECU. I checked for continuity between each of the field wires coming out of the molded rubber connector at the alternator end and used the alternator case for ground. The green wire did not have continuity, but the green/orange did. It seems like neither should be grounded, but a schematic shows that the green/orange wire also goes to the ignition coil and injectors. Is this grounded wire a problem or is it normal with something to do with the coil/injectors?
I did some checks for continuity with ground on the field wires. I disconnected the wires from the back of the alternator and also unplugged them from the ECU. I checked for continuity between each of the field wires coming out of the molded rubber connector at the alternator end and used the alternator case for ground. The green wire did not have continuity, but the green/orange did. It seems like neither should be grounded, but a schematic shows that the green/orange wire also goes to the ignition coil and injectors. Is this grounded wire a problem or is it normal with something to do with the coil/injectors?
Last edited by rmcrom; 09-10-2016 at 12:25 PM.