Rough running 90 4.0 HELP!
04-22-2013 | 04:59 PM
#17
Thread Starter
Newbie
Joined: Aug 2012
Posts: 19
Likes: 0
From: Muskegon, Michigan
Year: 1990
Model: Cherokee
Engine: 4.0 L
It just died on my I pulled out my multimeter and got a reading of .3 to .6v I know it needs .5v to run correctly. So looks like ill be replacing it with the proper CPS.
04-22-2013 | 05:03 PM
#18
::CF Moderator::
Joined: Aug 2011
Posts: 43,971
Likes: 1,565
From: Prescott, Az
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
Do this before installing the CPS, and be sure to route the wires properly.
Renix CPS Testing and Adjusting
Renix CPSs have to put out a strong enough signal to the ECU so that it will provide spark.
Most tests for the CPS suggest checking it for an ohms value. This is unreliable and can cause some wasted time and aggravation in your diagnosis of a no-start issue as the CPS will test good when in fact it is bad.
The problem with the ohms test is you can have the correct amount of resistance through the CPS but it isn’t generating enough voltage to trigger the ECU to provide spark.
Unplug the harness connector from the CPS. Using your voltmeter set on AC volts and probing both wires in the connector going to the CPS, crank the engine over. It won’t start with the CPS disconnected.
You should get a reading of .5 AC volts.
If you are down in the .35 AC volts range or lower on your meter reading, you can have intermittent crank/no-start conditions from your Renix Jeep. Some NEW CPSs (from the big box parts stores) have registered only .2 AC volts while reading the proper resistance!! That’s a definite no-start condition. Best to buy your CPS from Napa or the dealer.
Sometimes on a manual transmission equipped Renix Jeep there is an accumulation of debris on the tip of the CPS. It’s worn off clutch material and since the CPS is a magnet, the metal sticks to the tip of the CPS causing a reduced voltage signal. You MAY get by with cleaning the tip of the CPS off.
A little trick for increasing the output of your CPS is to drill out the upper mounting hole to 3/8" from the stock 5/16", or slot it so the CPS bracket rests on the bell housing when pushed down. Then, when mounting it, hold the CPS down as close to the flywheel as you can while tightening the bolts.
Revised 01-26-2013
Renix CPS Testing and Adjusting
Renix CPSs have to put out a strong enough signal to the ECU so that it will provide spark.
Most tests for the CPS suggest checking it for an ohms value. This is unreliable and can cause some wasted time and aggravation in your diagnosis of a no-start issue as the CPS will test good when in fact it is bad.
The problem with the ohms test is you can have the correct amount of resistance through the CPS but it isn’t generating enough voltage to trigger the ECU to provide spark.
Unplug the harness connector from the CPS. Using your voltmeter set on AC volts and probing both wires in the connector going to the CPS, crank the engine over. It won’t start with the CPS disconnected.
You should get a reading of .5 AC volts.
If you are down in the .35 AC volts range or lower on your meter reading, you can have intermittent crank/no-start conditions from your Renix Jeep. Some NEW CPSs (from the big box parts stores) have registered only .2 AC volts while reading the proper resistance!! That’s a definite no-start condition. Best to buy your CPS from Napa or the dealer.
Sometimes on a manual transmission equipped Renix Jeep there is an accumulation of debris on the tip of the CPS. It’s worn off clutch material and since the CPS is a magnet, the metal sticks to the tip of the CPS causing a reduced voltage signal. You MAY get by with cleaning the tip of the CPS off.
A little trick for increasing the output of your CPS is to drill out the upper mounting hole to 3/8" from the stock 5/16", or slot it so the CPS bracket rests on the bell housing when pushed down. Then, when mounting it, hold the CPS down as close to the flywheel as you can while tightening the bolts.
Revised 01-26-2013
04-22-2013 | 06:33 PM
#20
::CF Moderator::
Joined: Aug 2011
Posts: 43,971
Likes: 1,565
From: Prescott, Az
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
Thread
Thread Starter
Forum
Replies
Last Post
Ye Ol' Cherokee
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
3
04-25-2017 09:35 AM
David Chauncey Clothier
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
2
08-29-2015 10:31 PM
DanO55
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
1
08-28-2015 08:16 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)