Stupid beginner questions
#1
Senior Member
Thread Starter
Stupid beginner questions
My new-to-me '99 Cherokee came without an owner's manual and, as far as I can tell, without a jack (unless it's in a hidden storage location somewhere). There is what appears to be a foldable crank for working a jack laying in the back.
So where does the jack normally stow? Does it go on the hook that holds the spare tire? Doing web searches I'm seeing both bottle and scissor type jacks, what is the correct one for this vehicle? Where are the jacking points?
Also, was there a cargo cover available for the back area to keep stuff hidden? (The AMC Eagle wagon this replaced had a window-shade type arrangement for that. I don't see an obvious place to put anything similar here.)
So where does the jack normally stow? Does it go on the hook that holds the spare tire? Doing web searches I'm seeing both bottle and scissor type jacks, what is the correct one for this vehicle? Where are the jacking points?
Also, was there a cargo cover available for the back area to keep stuff hidden? (The AMC Eagle wagon this replaced had a window-shade type arrangement for that. I don't see an obvious place to put anything similar here.)
#5
Member
Join Date: Jun 2015
Location: Towson, MD USA
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1992
Model: Cherokee
Engine: 4.0 Litre High Output
A retractable tonneau cover was a *rare* option for early XJ's and few have survived. If you can find one on ebay or in a junkyard more power to you. If you look in your cargo area you can see the cutouts and mounting spots for it.
#6
CF Veteran
Join Date: Jul 2013
Location: Monett, MO.
Posts: 7,554
Likes: 0
Received 15 Likes
on
15 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Welcome to the forum!
The jack points are located on the frame rail in front right before the curved section behind the tire, the rear also on the straight section close to the rear tire.
BTW I guess you did know the 99 XJ's were the most desirable year of them all. The very best of all the older ones with and newest additions and none of the problems like with the 00/01 XJ's have.
The jack points are located on the frame rail in front right before the curved section behind the tire, the rear also on the straight section close to the rear tire.
BTW I guess you did know the 99 XJ's were the most desirable year of them all. The very best of all the older ones with and newest additions and none of the problems like with the 00/01 XJ's have.
#7
CF Veteran
Join Date: Aug 2010
Location: Canton, MI
Posts: 8,357
Likes: 0
Received 90 Likes
on
74 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Welcome to the forum!
The jack points are located on the frame rail in front right before the curved section behind the tire, the rear also on the straight section close to the rear tire.
BTW I guess you did know the 99 XJ's were the most desirable year of them all. The very best of all the older ones with and newest additions and none of the problems like with the 00/01 XJ's have.
The jack points are located on the frame rail in front right before the curved section behind the tire, the rear also on the straight section close to the rear tire.
BTW I guess you did know the 99 XJ's were the most desirable year of them all. The very best of all the older ones with and newest additions and none of the problems like with the 00/01 XJ's have.
Trending Topics
#9
Senior Member
Thread Starter
Thanks guys - I looked under the seat and the bracket to hold the jack down is there, but no jack. I'll have to get one at a junkyard or eBay. Actually a hydraulic bottle jack would probably be a nice upgrade but I haven't seen any that have the same kind of platform with "ears" sticking up on them like the factory jack. There's enough of the jacking instructions sticker left that I can see it shows using the jack on the axle tubes.
I didn't know when I bought this that '99 was the most desirable year, it was just dumb luck on my part. I was just looking for something decent and not too expensive that I could pick up and get sorted out before the bad weather arrives.
Fortunately this one needed minimal sorting out. I just got done painting the bumpers and aux light support, with that and the bedliner sprayed on the fender flares it's actually looking pretty sharp! I'd also like to add lower door moldings that I've seen on some Cherokees mainly so the rusty/fiberglassed lower area on the front passenger door is covered up. I'll have to keep an eye out in the junkyards. (I assume they're glued on or use double-stick tape.)
Last thing that needs to be done is to install the replacement rear wiper motor I picked up. I started another thread for my other stupid question of how to get the inner plastic panel off the tailgate. After removing screws and pull handle there is still "something" holding it in place and I don't want to break it by forcing too hard.
I didn't know when I bought this that '99 was the most desirable year, it was just dumb luck on my part. I was just looking for something decent and not too expensive that I could pick up and get sorted out before the bad weather arrives.
Fortunately this one needed minimal sorting out. I just got done painting the bumpers and aux light support, with that and the bedliner sprayed on the fender flares it's actually looking pretty sharp! I'd also like to add lower door moldings that I've seen on some Cherokees mainly so the rusty/fiberglassed lower area on the front passenger door is covered up. I'll have to keep an eye out in the junkyards. (I assume they're glued on or use double-stick tape.)
Last thing that needs to be done is to install the replacement rear wiper motor I picked up. I started another thread for my other stupid question of how to get the inner plastic panel off the tailgate. After removing screws and pull handle there is still "something" holding it in place and I don't want to break it by forcing too hard.
#10
CF Veteran
Join Date: May 2015
Location: Arizona
Posts: 4,481
Likes: 0
Received 18 Likes
on
14 Posts
Year: 97
Model: Cherokee
Engine: 4.0
Worm drive
Thanks guys - I looked under the seat and the bracket to hold the jack down is there, but no jack. I'll have to get one at a junkyard or eBay. Actually a hydraulic bottle jack would probably be a nice upgrade but I haven't seen any that have the same kind of platform with "ears" sticking up on them like the factory jack. There's enough of the jacking instructions sticker left that I can see it shows using the jack on the axle tubes.
I didn't know when I bought this that '99 was the most desirable year, it was just dumb luck on my part. I was just looking for something decent and not too expensive that I could pick up and get sorted out before the bad weather arrives.
Fortunately this one needed minimal sorting out. I just got done painting the bumpers and aux light support, with that and the bedliner sprayed on the fender flares it's actually looking pretty sharp! I'd also like to add lower door moldings that I've seen on some Cherokees mainly so the rusty/fiberglassed lower area on the front passenger door is covered up. I'll have to keep an eye out in the junkyards. (I assume they're glued on or use double-stick tape.)
Last thing that needs to be done is to install the replacement rear wiper motor I picked up. I started another thread for my other stupid question of how to get the inner plastic panel off the tailgate. After removing screws and pull handle there is still "something" holding it in place and I don't want to break it by forcing too hard.
I didn't know when I bought this that '99 was the most desirable year, it was just dumb luck on my part. I was just looking for something decent and not too expensive that I could pick up and get sorted out before the bad weather arrives.
Fortunately this one needed minimal sorting out. I just got done painting the bumpers and aux light support, with that and the bedliner sprayed on the fender flares it's actually looking pretty sharp! I'd also like to add lower door moldings that I've seen on some Cherokees mainly so the rusty/fiberglassed lower area on the front passenger door is covered up. I'll have to keep an eye out in the junkyards. (I assume they're glued on or use double-stick tape.)
Last thing that needs to be done is to install the replacement rear wiper motor I picked up. I started another thread for my other stupid question of how to get the inner plastic panel off the tailgate. After removing screws and pull handle there is still "something" holding it in place and I don't want to break it by forcing too hard.
Then it probably had a worm drive jack that looks similar to a Bottle Jack, mine was missing also when I got it. A real Bottle jack is not a bad idea
#11
Senior Member
Thread Starter
Yes, that's the type. I've seen them on eBay. The problem is that every hydraulic bottle jack I've seen only has a small flat top on the piston and that's not going to be stable lifting on the axle tube.
#14
Senior Member
Thread Starter
I'm surprised no one sells a real bottle jack like that, it's a pretty obviously useful thing for lifting up on axles or even frame rails. Never seen one though. (I guess that doesn't mean they're not out there somewhere.)