Transmission flush
#1
Newbie
Thread Starter
Join Date: Nov 2018
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee (XJ)
Transmission flush
So my 97 xj is a little over 200k don’t know if previous owner has done any tune up but purchased parkplugs, and wiring harness and distributor and all that gonna be doing my transmission but was wonder when I flush it can anyone help and tell me or show me which hose to disconnect to flush it?
#2
Senior Member
Join Date: Mar 2014
Location: Cincinnati, Ohio
Posts: 539
Likes: 0
Received 4 Likes
on
4 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Do not flush, over the next 3-4 oil changes just drain as much transmission fluid as will come out from the drain plug and refill. Flushing can cause dirt to break loose that is not hurting anyting right now but can damage if it comes loose. It normally takes around 3-4 oil changes for the fluid to start looking good again and you are set.
Use Dex Merc lll for the fills.
Use Dex Merc lll for the fills.
#3
CF Veteran
There is no problem with flushing it as long as you use the transmission pump to pump the old fluid out, while you are adding new fluid, don't use a machine to flush it. You can cut either one of the soft lines towards the front then put a drain pan underneath and have someone start the jeep real quick so you can see which way the fluid is flowing. Then you just clamp your hose on it, and run the jeep while slowly adding fluid untill the fluid coming out looks clean. Then you put the hose back together with some barbed fittings and hose clamps. Of course there is nothing wrong with the drain and refill method either, but if you do it this way you can get it all at once.
#4
Newbie
Thread Starter
Join Date: Nov 2018
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee (XJ)
Do not flush, over the next 3-4 oil changes just drain as much transmission fluid as will come out from the drain plug and refill. Flushing can cause dirt to break loose that is not hurting anyting right now but can damage if it comes loose. It normally takes around 3-4 oil changes for the fluid to start looking good again and you are set.
Use Dex Merc lll for the fills.
Use Dex Merc lll for the fills.
#5
Senior Member
I think the drain plug takes a 14mm wrench. About 4 quarts will drain. Replace the lost fluid, drive for X amount of time, then drain again. When the color turns back to a decent red, your done. Use DexMerc III
#6
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,971
Received 1,559 Likes
on
1,263 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
#7
Newbie
Join Date: Nov 2018
Location: London. Ohio, USA
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee (XJ)
Engine: 4.0L I6
While your at this process, go ahead and change your transfer case fluids too. Uses the same Dex/Merc III as your trans.
Trending Topics
#8
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,971
Received 1,559 Likes
on
1,263 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
Agreed. Don't use a machine flush on older transmissions. Doing this gradually is much more gentle and less likely to kick-up all the crud that can damage the internals. Be sure to clean your pan and replace filter during this process. When I did this before I rebuilt my AW4, I drained, replaced filter, and added the 4 quarts that drained out. Drove it about 100-200 miles, then drained and filled again.
While your at this process, go ahead and change your transfer case fluids too. Uses the same Dex/Merc III as your trans.
While your at this process, go ahead and change your transfer case fluids too. Uses the same Dex/Merc III as your trans.
#10
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,971
Received 1,559 Likes
on
1,263 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
#12
Junior Member
There is no problem with flushing it as long as you use the transmission pump to pump the old fluid out, while you are adding new fluid, don't use a machine to flush it.
You can cut either one of the soft lines towards the front then put a drain pan underneath and have someone start the jeep real quick so you can see which way the fluid is flowing. Then you just clamp your hose on it, and run the jeep while slowly adding fluid untill the fluid coming out looks clean. Then you put the hose back together with some barbed fittings and hose clamps.......................
You can cut either one of the soft lines towards the front then put a drain pan underneath and have someone start the jeep real quick so you can see which way the fluid is flowing. Then you just clamp your hose on it, and run the jeep while slowly adding fluid untill the fluid coming out looks clean. Then you put the hose back together with some barbed fittings and hose clamps.......................
This is the best way of doing it by far since it will get all the AT fluid changed at once, including torque converter, oil cooler(s) and lines!
I hear what cruiser54 is saying about no need to remove & clean the pan and he may be right, but I would still remove the pan first and clean it since it's unknown if it was ever done by the previous owner.
Just saying
🤔
#14
Junior Member
This identifies the AW4's two AT fluid lines:
(Should be easy to find convenient spot do disconnect somewhere close to radiator / AT cooler)
The author is someone else on one of these Jeep forums!
#15
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,971
Received 1,559 Likes
on
1,263 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
Post a pic of the screen you remove please.