Urgent! Drive shaft problem
#1
Seasoned Member
Thread Starter
Join Date: Feb 2009
Location: Wenatchee,WA
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Grand Cherokee
Engine: 5.2L V8
Urgent! Drive shaft problem
Yesterday I was pulling out of my neighborhood and heard a big knocking noise. So I check it out and my rear drive shaft had come off where it connects to the rear axle. A buddy of mine said I needed to replace the u-joint, so I purchased a new one, but now I just need to know how to replace it. If any one could please help that'd be greatly appreciated. Thanks!
#2
CF Veteran
Join Date: Nov 2008
Location: Eugene, OR
Posts: 1,251
Likes: 0
Received 0 Likes
on
0 Posts
Year: 01
Model: Cherokee
Engine: 4.0L I6
is the yoke still intact? did you lose any hardware when it "fell out," like the bolts or the straps. i dont have a write up on changing them, but im sure someone can provide something for you. i've always seen it done with a hammer and a socket about the same size as the cap to punch it out.
#5
::CF Administrator::
Join Date: May 2008
Location: Okc area
Posts: 10,039
Likes: 0
Received 16 Likes
on
11 Posts
Year: 1991
Model: Cherokee
Engine: 4.0 I6
If you need to rebuild the front driveshaft here's a really good writeup for that..
http://www.myjeepxj.com/index.php?pa...-shaft-rebuild
http://www.myjeepxj.com/index.php?pa...-shaft-rebuild
#6
Seasoned Member
Thread Starter
Join Date: Feb 2009
Location: Wenatchee,WA
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Grand Cherokee
Engine: 5.2L V8
I spent about 3 hours trying to get that u-joint out with no sucess at all Is there any other way to do it? Thanks
Trending Topics
#8
Seasoned Member
Thread Starter
Join Date: Feb 2009
Location: Wenatchee,WA
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Grand Cherokee
Engine: 5.2L V8
#9
Junior Member
Join Date: Jan 2009
Location: North Georgia U.S.A.
Posts: 50
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0L High Output
If so did you remember to remove the snap ring?
#10
Seasoned Member
Thread Starter
Join Date: Feb 2009
Location: Wenatchee,WA
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Grand Cherokee
Engine: 5.2L V8
Did you follow the instructions on this site, http://jeepin.com/features/ujoint/index.asp
If so did you remember to remove the snap ring?
If so did you remember to remove the snap ring?
#11
Seasoned Member
Thread Starter
Join Date: Feb 2009
Location: Wenatchee,WA
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Grand Cherokee
Engine: 5.2L V8
If anyone knows of another technique to remove the u-joint, it would be greatly appreciated. Thanks
#12
::CF Administrator::
Join Date: May 2008
Location: Okc area
Posts: 10,039
Likes: 0
Received 16 Likes
on
11 Posts
Year: 1991
Model: Cherokee
Engine: 4.0 I6
get a ball joint press and try that..I use the socket and big mallet hammer and smack the crap out of it..If it's seized that bad wow..Maybe get some silicon spray lube and hose it down and let it sit a sec and see if it will loosen up.
#13
Junior Member
Join Date: Jan 2009
Location: North Georgia U.S.A.
Posts: 50
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0L High Output
#15
Seasoned Member
Thread Starter
Join Date: Feb 2009
Location: Wenatchee,WA
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Grand Cherokee
Engine: 5.2L V8
I still can't seem to get it out.. :/ It's loose in there now, just can't pop either of the caps out so I can remove it. I'd cut it but don't have anything to do that at the moment. Any other ideas?