Last edit by: IB Advertising
See related guides and technical advice from our community experts:
Browse all: General Overview
- Jeep Grand Cherokee WJ 1999 to 2004 Crash Test and Safety Ratings
Important Information to help you understand your Jeep Grand Cherokee.
Browse all: General Overview
XJ Ask the Question Thread
CF Veteran
Join Date: Aug 2010
Location: The Florida State University
Posts: 8,387
Likes: 0
Received 1 Like
on
1 Post
Year: 2001
Model: Cherokee
Engine: I-6 4.0 L
Originally Posted by vegasjms
I was having issues with sparatic idol. Upon start up would rev high & drop to near stall and just "gallop" until it warmed and then even out. The other morning it was freezing cold, vehicle was covered in ice and it wouldn't start. It wanted to but it was like something was holding it back....ok, long story short got someone to get it started for me and was advised to replace tps. Well I replaced the sensor yesterday and it made a world of difference the engine runs much smoother and the "gallop" sound is gone, only concern I have is that the resting idol is much higher than it was. Is there a reset or something that needs to be done after having this part replaced? I got the part from napa (echlin line).
Thanks, Jenn
96 Cherokee 4.0
Thanks, Jenn
96 Cherokee 4.0
CF Veteran
Join Date: Sep 2010
Location: Mercer County, NJ
Posts: 12,692
Likes: 0
Received 4 Likes
on
4 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L I6 HO
Originally Posted by cf1k1
Disconnect the POSTIVE POWER WIre at the battery and touch it to the ground post on the battery. REMEMBER POSTIVE WIRE!! Reconnect positive wire. Turn to to RUN postition but do not start. Turn head lights on. Turn heads light off. Turn key to off
CF Veteran
Join Date: Oct 2011
Location: Summerville, South Carolina
Posts: 2,613
Likes: 0
Received 0 Likes
on
0 Posts
Year: 99
Model: Cherokee
Engine: 4.0
I started adding AAL to my rear passenger side springs. After 2 hours I got it together but now the bottom of the spring pin is NOT lining up with the axle mount. What do I do?
Originally Posted by zombie jeep101
I started adding AAL to my rear passenger side springs. After 2 hours I got it together but now the bottom of the spring pin is NOT lining up with the axle mount. What do I do?
Seasoned Member
Join Date: Oct 2012
Location: CA
Posts: 444
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0L Inline 6
are you sure you put the AAL in the right way? correct me if im wrong really. but i know AALs the eleaf u are addin its center pin hole isnt centered. u have put it in the right direction when installin it within ur stock pack to make everything line up?
Dumb question im askin but may i ask why ur only AALing one side?
Dumb question im askin but may i ask why ur only AALing one side?
CF Veteran
Join Date: Oct 2011
Location: Summerville, South Carolina
Posts: 2,613
Likes: 0
Received 0 Likes
on
0 Posts
Year: 99
Model: Cherokee
Engine: 4.0
Originally Posted by jeeperscreepers92
are you sure you put the AAL in the right way? correct me if im wrong really. but i know AALs the eleaf u are addin its center pin hole isnt centered. u have put it in the right direction when installin it within ur stock pack to make everything line up?
Dumb question im askin but may i ask why ur only AALing one side?
And I'm not only doing one side, I'm just working on one side at a time
Seasoned Member
Join Date: Oct 2012
Location: CA
Posts: 444
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0L Inline 6
CF Veteran
Join Date: Sep 2010
Location: Mercer County, NJ
Posts: 12,692
Likes: 0
Received 4 Likes
on
4 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L I6 HO
Originally Posted by zombie jeep101
I never took the top leaf out so I know it's centered. Ima try to ratchet it into place tomorrow.
And I'm not only doing one side, I'm just working on one side at a time
CF Veteran
Join Date: Mar 2010
Location: Jacksonville, FL
Posts: 6,685
Likes: 0
Received 5 Likes
on
5 Posts
Year: 92
Model: Cherokee
Engine: 4.0
Originally Posted by jeeperscreepers92
yo anyone have have an idea if when i replace my piston rings at 212k miles if i need to rebore my block?
hone? recommended
Seasoned Member
Join Date: Oct 2012
Location: CA
Posts: 444
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990
Model: Cherokee
Engine: 4.0L Inline 6
but i should have no problems pushin the pistons out the top right? i know i have asked this tons of times. hey anybody know of a good write up to do this with? any special tools. first time i dealt with rings before (I hate pullin apart motors...cuz emergency comes up and i never have time to finish up every single time.)
any recommended sizepiston rings i should buy? cuz i dont want to pull apart the pan and the head twice and spend more money on oil and coolant. i just want to do the job once and do it right and get all over with in one solid go.
any recommended sizepiston rings i should buy? cuz i dont want to pull apart the pan and the head twice and spend more money on oil and coolant. i just want to do the job once and do it right and get all over with in one solid go.