Last edit by: IB Advertising
See related guides and technical advice from our community experts:
Browse all: General Overview
- Jeep Grand Cherokee WJ 1999 to 2004 Crash Test and Safety Ratings
Important Information to help you understand your Jeep Grand Cherokee.
Browse all: General Overview
XJ Ask the Question Thread
Newbie
Join Date: Apr 2014
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Year: 86
Model: Cherokee
Engine: 2.8
squeaky
So I replaced the water pump and belt a few weeks back on my 99 xj limited and ever since then on start up the belt squeaks quite obnoxiously. Also while at idle if I have my overhead light bar on it'll start to squeak also. Not sure how to fix this problem.
CF Veteran
Join Date: Aug 2012
Location: ks
Posts: 1,539
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
2. At idle in park, place your hand on the light bar and apply pressure. Does the noise go away? Tighten it, lube it, add rubber insulators.......
Last edited by straightsixjeep; 04-10-2014 at 10:39 PM.
CF Veteran
Join Date: Nov 2013
Location: Wetumpka, AL
Posts: 1,347
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1987
Model: Cherokee
Engine: 4.0
87 xj 4.0 auto
When i crank it the rpm's will shoot up to around 1600 rpm and the lifters are loud. It will immediately settle back down to normal idle and drives fine with no lifter noise. Any ideas?
When i crank it the rpm's will shoot up to around 1600 rpm and the lifters are loud. It will immediately settle back down to normal idle and drives fine with no lifter noise. Any ideas?
Herp Derp Jerp
Join Date: Nov 2011
Location: Parham, ON
Posts: 18,251
Likes: 0
Received 13 Likes
on
12 Posts
Year: 1999
Model: Cherokee
Engine: 4.0L OBD-II
Herp Derp Jerp
Join Date: Nov 2011
Location: Parham, ON
Posts: 18,251
Likes: 0
Received 13 Likes
on
12 Posts
Year: 1999
Model: Cherokee
Engine: 4.0L OBD-II
I want to do some general maintenance to my 1991 XJ 4x4 5 speed. I just bought it last week and I've done coolant flush, power steering flush, oil change, new battery and terminals. Now I want to change the front/rear axle fluid/manual tranny fluid/transfer case oil. I was planning on using Mobile 1 synthetic 75w90 for everything except the rear axle (75w140). I need to know how many quarts of oil I will need, I have a budget of 80 bucks right now so what would you do first? Transmission and rear differential? I found gear oil for 12.00 qt shipped from amazon.
The transmission does not use API GL-5 gear oil; it is for hypoid gears only and corrosive to brass. You want a purpose made lube compatible with synchronized gear boxes. Redline MT-90, Royal Purple Synchromax, Pennzoil Synchromesh, and ACDelco Synchromesh fluids all work, with MT-90 being the king of the castle. Roughly 3.5 quarts.
The transfer case takes slightly over 1 quart of ATF. Never put gear oil in it.
Rear axle depends on which one you have. Two bottles of 75w140, top it off with leftover from the front axle if required.
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,971
Received 1,559 Likes
on
1,263 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
Possibly the TPS is going bad and you've got a cheapy oil filter.
CF Veteran
Join Date: Nov 2013
Location: Wetumpka, AL
Posts: 1,347
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1987
Model: Cherokee
Engine: 4.0
K&N filter, which isnt normally what i use (usually a mobil 1). I'll check the TPS this weekend. I havent been driving it much lately. Thanks Cruiser
::CF Moderator::
Join Date: Aug 2011
Location: Prescott, Az
Posts: 43,971
Received 1,559 Likes
on
1,263 Posts
Year: 1990
Model: Cherokee (XJ)
Engine: 4.0
So the last few weeks I've been having this issue with my '99 xj 4.0. I'll be driving normal around town and it will suddenly lose power. Like turning out on to a rode to accelerate to 30-45 mph and it will hesitate/sputter/backfire... You can blip the throttle some and it will feel like its popping but won't go then it will clear up and take off like normal.
Also if it goes into this rough running mode and I'm at a stop, it'll idle low like <500 on the tach, and of course it'll be a bit rougher idle. Oil pressure is fine.
I checked the plug wires to make sure one didn't loosen up. The center wire on the distributor clicked as it apparently wasn't fully seated. I thought this had fixed this issue but no it happened one more time since then.
Any ideas? TPS? Transmission? I'm going to check the fluid just to be safe. Then maybe pull the plugs.
Also if it goes into this rough running mode and I'm at a stop, it'll idle low like <500 on the tach, and of course it'll be a bit rougher idle. Oil pressure is fine.
I checked the plug wires to make sure one didn't loosen up. The center wire on the distributor clicked as it apparently wasn't fully seated. I thought this had fixed this issue but no it happened one more time since then.
Any ideas? TPS? Transmission? I'm going to check the fluid just to be safe. Then maybe pull the plugs.
Member
Join Date: Apr 2012
Location: Minersville Pennsylvania
Posts: 119
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1991
Model: Cherokee
Engine: 4.0 H.O.
Redline MT-90, Royal Purple Synchromax, Pennzoil Synchromesh, and ACDelco Synchromesh fluids all work, with MT-90 being the king of the castle. Roughly 3.5 quarts.
The transfer case takes slightly over 1 quart of ATF. Never put gear oil in it.
Rear axle depends on which one you have. Two bottles of 75w140, top it off with leftover from the front axle if required.
The transfer case takes slightly over 1 quart of ATF. Never put gear oil in it.
Rear axle depends on which one you have. Two bottles of 75w140, top it off with leftover from the front axle if required.
Junior Member
Join Date: Jun 2009
Location: PHX
Posts: 51
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Felpro blue.
Have you read this?
Valve cover can leak out the back and look like a rear main.
Oil filter adapter, distributor can look like a pan gasket leaking.....
I'd be looking up ABOVE first, and VERIFYING the source of the oil leak YOURSELF.
Everybody, who doesn't own or have to pay for or perform your vehicle repairs, loves to poke their noggin UNDER the Jeep and come out bearing the false bad news that your RMS is leaking.
Many mechanics, friends, people on Jeep forums who can’t see your Jeep from where they’re at, and good old Uncle Bob seem to enjoy telling you it’s the rear main seal. Has a catastrophic ring to it, doesn’t it?
A simple leak at the back of the valve cover or other source could produce the same symptoms. You don’t need to be a mechanic to figure this out. If you have good eyesight and a dim flashlight, you’re good to go on your own. Don't jump on the RMS/oil pan gasket bandwagon right off the bat.
Almost any oil leak on your 4.0 is gonna drip from the RMS area for two simple reasons.
First off, the engine sits nose-up and any oil will run back to the RMS area. Secondly, the RMS area is also the lowest point on the engine. Simple physics and the old plumber's adage apply here. "$hit flows downhill".
Valve cover gasket, oil pressure sending unit, oil filter adapter seals and distributor gasket, in that order, have to be eliminated as possibilities first.
Revised 02-26-2013
Have you read this?
Valve cover can leak out the back and look like a rear main.
Oil filter adapter, distributor can look like a pan gasket leaking.....
I'd be looking up ABOVE first, and VERIFYING the source of the oil leak YOURSELF.
Everybody, who doesn't own or have to pay for or perform your vehicle repairs, loves to poke their noggin UNDER the Jeep and come out bearing the false bad news that your RMS is leaking.
Many mechanics, friends, people on Jeep forums who can’t see your Jeep from where they’re at, and good old Uncle Bob seem to enjoy telling you it’s the rear main seal. Has a catastrophic ring to it, doesn’t it?
A simple leak at the back of the valve cover or other source could produce the same symptoms. You don’t need to be a mechanic to figure this out. If you have good eyesight and a dim flashlight, you’re good to go on your own. Don't jump on the RMS/oil pan gasket bandwagon right off the bat.
Almost any oil leak on your 4.0 is gonna drip from the RMS area for two simple reasons.
First off, the engine sits nose-up and any oil will run back to the RMS area. Secondly, the RMS area is also the lowest point on the engine. Simple physics and the old plumber's adage apply here. "$hit flows downhill".
Valve cover gasket, oil pressure sending unit, oil filter adapter seals and distributor gasket, in that order, have to be eliminated as possibilities first.
Revised 02-26-2013
and I cleaned up the whole engine compartment
I did some of that noggin pokin
I was havin a nostart issue anyway, so some simple green and a little extra time didn't seem to hurt
the valve cover wasn't tightened down near the fire wall
ant it was leaking. however so is rms
and the oil pan
this old engine has lots and lots of miles on it,
so since I don't start work for another week, and I may never have time again for at least a few years (i'm gonna be a dad come October)
I wanna do everything I can in the last bit of time I know I have
I even finally put in the aux lights ive had in the box for the past 2years
CF Veteran
Join Date: Oct 2009
Location: Fauquier County, Virginia
Posts: 2,867
Likes: 0
Received 15 Likes
on
13 Posts
Year: 1991
Model: Cherokee
Engine: I-6 4.0 HO
Is the stock trans power/comfort switch basically a simple bridge type switch that connects/disconnects two wires or does it switch between different circuits? I ask because I want to repurpose one as a simple fog light switch.
CF Veteran
Join Date: Feb 2013
Location: Justin, TEXAS
Posts: 1,802
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
You can wire two of the switch wires together to keep it in power mode. That's what I did and Im putting daystar switches in all 4 of those slots