Last edit by: IB Advertising
See related guides and technical advice from our community experts:
Browse all: General Overview
- Jeep Grand Cherokee WJ 1999 to 2004 Crash Test and Safety Ratings
Important Information to help you understand your Jeep Grand Cherokee.
Browse all: General Overview
XJ Ask the Question Thread
#5281
CF Veteran
Join Date: Dec 2010
Location: Missouri
Posts: 1,246
Likes: 0
Received 1 Like
on
1 Post
Year: 1998
Model: Cherokee
Engine: I6 4.0 L
Hello, I have a 98 4dr sport xj and it has remote locks. I can lock and unlock all of the doors just fine except the drivers door. The lock button on the inside will switch over to unlock or lock, whichever one selected, but it wont actually lock it. Any ideas on what to do? I need to get it to lock because I dont want anything stolen.... Thanks!!!
#5282
☠ CF Sheriff ☠
the rod came off the linkage inside the door. Open it up and reconnect it
#5283
CF Veteran
Join Date: Sep 2010
Location: Mercer County, NJ
Posts: 12,692
Likes: 0
Received 4 Likes
on
4 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L I6 HO
Originally Posted by Nperryman
Hello, I have a 98 4dr sport xj and it has remote locks. I can lock and unlock all of the doors just fine except the drivers door. The lock button on the inside will switch over to unlock or lock, whichever one selected, but it wont actually lock it. Any ideas on what to do? I need to get it to lock because I dont want anything stolen.... Thanks!!!
#5284
CF Veteran
Join Date: Dec 2010
Location: Missouri
Posts: 1,246
Likes: 0
Received 1 Like
on
1 Post
Year: 1998
Model: Cherokee
Engine: I6 4.0 L
Originally Posted by sycoglitch
If you can actually hear it locking and unlocking open the door up and make sure the 2 bars are in the plastic pieces. It's not hard to open up an xjs door three screws and a bunch if plastic clips
#5285
CF Veteran
Join Date: Sep 2010
Location: Mercer County, NJ
Posts: 12,692
Likes: 0
Received 4 Likes
on
4 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L I6 HO
Originally Posted by Nperryman
I did that and they are both latched in there. Actually the top one even pushes the button over when I lock it. ?????
#5286
Member
Join Date: Dec 2010
Location: NW FL
Posts: 229
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
ive got a 93 cherokee i just picked up for a trail rig. my buddies 01 just crapped out the tranny, floor is rusted, and the steering is shot so hes going to junk it. what are some parts i could pull off the 01 for my 93 to make it better? i know the intake manifold upgrade and front axle shafts are one piece with stronger ujoints. i would swap over my 27 spline for his 29 spline 8.25 but his shock mounts are broken and it has a leaking pinion seal. are there any other common upgrades?
#5287
Senior Member
Join Date: Jan 2010
Location: LARRYVILLE
Posts: 602
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
Originally Posted by Nperryman
I did that and they are both latched in there. Actually the top one even pushes the button over when I lock it. ?????
#5288
Newbie
Join Date: Jun 2011
Location: NJ
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: I6
np 231 issues
hey,
I just bought a 1996 cherokee country with the 4.0 straight 6...
having issues with the np231 transfer case:
It has a problem with the 4-Lo... I can shift the lever to the spot, but 4-Lo doesnt engage.the shifter moves where it needs to, but when i put it back in drive i get nothing... cant move at all. when i shift back out it grinds a little through neutrel but does into 4 hi or 2 fine and can move again. 4-high goes in with no problem. all the issues i've seen involving 4-lo talked about grinding or getting stuck.. any ideas on what causes this and/ or how i can fix it (as cheap as possible-im on a tight budget)
Thanks!
I just bought a 1996 cherokee country with the 4.0 straight 6...
having issues with the np231 transfer case:
It has a problem with the 4-Lo... I can shift the lever to the spot, but 4-Lo doesnt engage.the shifter moves where it needs to, but when i put it back in drive i get nothing... cant move at all. when i shift back out it grinds a little through neutrel but does into 4 hi or 2 fine and can move again. 4-high goes in with no problem. all the issues i've seen involving 4-lo talked about grinding or getting stuck.. any ideas on what causes this and/ or how i can fix it (as cheap as possible-im on a tight budget)
Thanks!
#5289
CF Veteran
Join Date: Sep 2010
Location: Mercer County, NJ
Posts: 12,692
Likes: 0
Received 4 Likes
on
4 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L I6 HO
Originally Posted by tabuono
hey,
I just bought a 1996 cherokee country with the 4.0 straight 6...
having issues with the np231 transfer case:
It has a problem with the 4-Lo... I can shift the lever to the spot, but 4-Lo doesnt engage.the shifter moves where it needs to, but when i put it back in drive i get nothing... cant move at all. when i shift back out it grinds a little through neutrel but does into 4 hi or 2 fine and can move again. 4-high goes in with no problem. all the issues i've seen involving 4-lo talked about grinding or getting stuck.. any ideas on what causes this and/ or how i can fix it (as cheap as possible-im on a tight budget)
Thanks!
I just bought a 1996 cherokee country with the 4.0 straight 6...
having issues with the np231 transfer case:
It has a problem with the 4-Lo... I can shift the lever to the spot, but 4-Lo doesnt engage.the shifter moves where it needs to, but when i put it back in drive i get nothing... cant move at all. when i shift back out it grinds a little through neutrel but does into 4 hi or 2 fine and can move again. 4-high goes in with no problem. all the issues i've seen involving 4-lo talked about grinding or getting stuck.. any ideas on what causes this and/ or how i can fix it (as cheap as possible-im on a tight budget)
Thanks!
#5290
Newbie
Join Date: Oct 2009
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0l
1993 Cherokee country electrical problem
hi all, new here. i need help really bad.... i am having some electrical gremlins that i cant seem to find. i have lost use of my low and intermittent wipers, dome lights(cig lighter still works?), interior lights and power door locks(power windows still work), and also my power seat............. any help or suggestions is greatly appreciated.
#5291
CF Veteran
Join Date: May 2010
Location: Western Michigan
Posts: 1,680
Likes: 0
Received 4 Likes
on
4 Posts
Year: 1993
Model: Grand Cherokee
Engine: 4.0l inline 6
hi all, new here. i need help really bad.... i am having some electrical gremlins that i cant seem to find. i have lost use of my low and intermittent wipers, dome lights(cig lighter still works?), interior lights and power door locks(power windows still work), and also my power seat............. any help or suggestions is greatly appreciated.
#5292
Newbie
Join Date: Oct 2009
Posts: 12
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993
Model: Cherokee
Engine: 4.0l
i have checked the fuses tore out the entire interior so i can follow all the wires from point a to point b in search of a broken wire just cant figure it out and dont know where to look for awnsers
#5293
CF Veteran
Join Date: Apr 2011
Location: Dayton Ohio
Posts: 2,080
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998 classic
Model: Cherokee
Engine: 4.0!!
i have a 96 country high output auto and a 99 auto both complete cherokees. im wondering if im going to run into any wiring problems when i put the drive train from the 96 into the 99? they both have power everything and all that. im just curious if i can just swap harness and pcm with the engine and be ok. or if i even need to do that. as for everything else ill be fine. going to be swapping next week. should be fun lol.
#5294
Member
Join Date: Oct 2010
Location: Spokane, WA
Posts: 212
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0
Ok, so we replaced our abs system with a dual diaphragm setup and are having problems braking. We replaced all of the components with new besides the mc, booster, proportioning valve, and all of the lines. So, should we start with the master cylinder, or the lines? Maybe the booster? Oh and we have bleed everything! Any ideas?
Sent using CherokeeFM
Sent using CherokeeFM