Northern Utah BS thread
#5116
CF Veteran
Join Date: May 2009
Location: SLC, UT
Posts: 6,328
Likes: 0
Received 1 Like
on
1 Post
Year: 1989 2 door
Model: Cherokee
Engine: 4.0
Might sound crazy, but a stethoscope against the bell housing will clear up the fly wheel in question... Either you'll hear the rattle inside or not!
#5118
Seasoned Member
Join Date: Jan 2011
Location: fairview utah
Posts: 423
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
Originally Posted by up_yours_7
Where is the best junkyard to get a rear window for cheap?
#5119
Senior Member
Join Date: Jul 2010
Location: Tooele, UT
Posts: 575
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0L I6
Little to far for me that's a three hour drive lol. I know penguin auto has one already pulled for 60 or I can try to get one myself from pull n save for 30.
#5120
CF Veteran
Join Date: Aug 2009
Location: Herriman, Utah
Posts: 1,534
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Cherokee
Engine: 4.0
#5123
Senior Member
Join Date: Nov 2009
Location: SLC Utah
Posts: 842
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: I6
i agree with ryan, 5mile is a really hard trail to find i had to set it in my gps when i started heading out there. And if you can tag along on the 26 you should its going to be a blast
Last edited by mike20; 02-12-2011 at 12:18 PM.
#5124
CF Veteran
Join Date: Aug 2010
Location: Huricane, Utah
Posts: 1,326
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994 Ford Bronco
Model: Cherokee
Engine: 351 W
I'd have someone rev it up for you IN PARK, while ya look around the under carriage for a rattling heat shield, trim, skid plate, shift linkage ect. Before ya start ripping into the tranny!
Might sound crazy, but a stethoscope against the bell housing will clear up the fly wheel in question... Either you'll hear the rattle inside or not!
Might sound crazy, but a stethoscope against the bell housing will clear up the fly wheel in question... Either you'll hear the rattle inside or not!
#5125
CF Veteran
Join Date: Aug 2010
Location: Huricane, Utah
Posts: 1,326
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994 Ford Bronco
Model: Cherokee
Engine: 351 W
#5126
Seasoned Member
Join Date: Jan 2011
Location: fairview utah
Posts: 423
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
Originally Posted by A.T.R.Offroad
Good idea ryan! another thing I haven't seen anyone mention is it could be you pilot bearing going out depending on the mileage on the vehicle. or throwout bearing.. Or if you have a internal slave cylinder that one.
#5128
CF Veteran
Join Date: Sep 2010
Location: Springville, UT
Posts: 1,649
Likes: 0
Received 1 Like
on
1 Post
Year: 1993
Model: Grand Cherokee
Engine: 5.2 V8, Dual cold air, dual batts, E-fan, Sanden OBA
lincoln locker?? its welding the spider gears together.... only problem is when welds break, or worse shafts, pinions, ring gears, etc..
#5129
CF Veteran
Join Date: Aug 2009
Location: Herriman, Utah
Posts: 1,534
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Cherokee
Engine: 4.0
#5130
CF Veteran
Join Date: Jan 2009
Location: Utardiland
Posts: 1,703
Likes: 0
Received 0 Likes
on
0 Posts
Year: whats left of a 91
Model: Cherokee
Engine: one that makes noise