South Florida Dysfunctional 4x4's
No, I don't lick fish.
Good evening, guys... if all works out, should have a "new" fuel tank, a new fuel pump, and MAAAAYYYYBEEEEE a new winch bumper and roof basket from the junkyard We'll see if it's still on the Jeep when I get there.
Newbie
Join Date: Sep 2015
Location: Jupiter FL
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Year: 97
Model: Cherokee
Engine: 4.0
Going to be a bit of an involved process but I need to strip the spray paint the PO used to see if there are any other spots that need attention. Aircraft paint remover it is.
Ill tack weld/seam seal the new plate, then clean all the remaining surface rust use rustoleum clean metal primer put a few coats down of that on the whole floor. Then put carpet back in (I DD my jeep so noise and heat reduction is welcomed)
Last edited by thescreensvers; 09-21-2017 at 06:14 PM.
CF Veteran
Join Date: Oct 2013
Location: Miami, fl
Posts: 7,378
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
I just saw it on the website lol...
::CF Administrator::
Join Date: Sep 2010
Location: Lantana, Fl
Posts: 34,052
Received 236 Likes
on
188 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.Slow
yea I need too much hah my whole drivers side is bad to like halfway under my seat and some patches here and there.
Going to be a bit of an involved process but I need to strip the spray paint the PO used to see if there are any other spots that need attention. Aircraft paint remover it is.
Ill tack weld/seam seal the new plate, then clean all the remaining surface rust use rustoleum clean metal primer put a few coats down of that on the whole floor. Then put carpet back in (I DD my jeep so noise and heat reduction is welcomed)
Going to be a bit of an involved process but I need to strip the spray paint the PO used to see if there are any other spots that need attention. Aircraft paint remover it is.
Ill tack weld/seam seal the new plate, then clean all the remaining surface rust use rustoleum clean metal primer put a few coats down of that on the whole floor. Then put carpet back in (I DD my jeep so noise and heat reduction is welcomed)
No, I don't lick fish.
CF Veteran
Join Date: Oct 2013
Location: Miami, fl
Posts: 7,378
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
CF Veteran
Thread Starter
Join Date: Mar 2010
Location: Broward County Fl.
Posts: 47,923
Likes: 0
Received 29 Likes
on
28 Posts
Year: 1989 xj sport 2dr
Model: Cherokee
Engine: 12 hole bosch Injectors
Morning all...Any non cad dana 30s around wanna get rid of my adjustable ball joint outer cs ?
::CF Administrator::
Join Date: Sep 2010
Location: Lantana, Fl
Posts: 34,052
Received 236 Likes
on
188 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.Slow
Only non-CAD axle is the spare 4.56 geared, Spartan locked one going in my MJ. Just picked up a 93 AX-15 and 231 for trade on a spare engine block I had. Score!
CF Veteran
Join Date: Oct 2013
Location: Miami, fl
Posts: 7,378
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
CF Veteran
Join Date: Oct 2013
Location: Miami, fl
Posts: 7,378
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
::CF Administrator::
Join Date: Sep 2010
Location: Lantana, Fl
Posts: 34,052
Received 236 Likes
on
188 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.Slow
CF Veteran
Join Date: Oct 2013
Location: Miami, fl
Posts: 7,378
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
CF Veteran
Join Date: Oct 2013
Location: Miami, fl
Posts: 7,378
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
No, I don't lick fish.
Welp.... they were LONG gone by the time I got there lol. Oh well.. managed to pick up a set of 5.9 ZJ hood vents, a 94-96 dash trim bezel (smoother plus someone had cut on mine around the radio and it was annoying me), some parts for my wife's car, and a license plate bracket off an Olds Aurora... Jeep is finally gonna have some kickass reverse lights.
Nice! Made out like a bandit on that one, Lee.
Nice! Made out like a bandit on that one, Lee.