Maryland Cherokee Club
CF Veteran
CF Veteran
Join Date: Nov 2011
Location: Nashville
Posts: 2,752
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
Mine sits at 9 when warmed up. My sending unit is bad and needs to be replaced. I was worried until a shop told me it runs 50's with a mech gauge. Get it tested for piece of mind.
CF Veteran
Join Date: Nov 2011
Location: Nashville
Posts: 2,752
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
I was looking at this one from JCR- http://www.jcroffroad.com/mm5/mercha...Code=1TNST-OTK
Just need to figure out whether I want to do under / over the knuckle
Just need to figure out whether I want to do under / over the knuckle
☠ CF Sheriff ☠
Spec is:
No less than 13psi at HOT idle
35-75psi over 1600 rpm, and when cold
Originally Posted by McGXJ
I was looking at this one from JCR- http://www.jcroffroad.com/mm5/mercha...Code=1TNST-OTK
Just need to figure out whether I want to do under / over the knuckle
Just need to figure out whether I want to do under / over the knuckle
Seasoned Member
Join Date: Aug 2010
Location: Ashburn, VA
Posts: 390
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
Originally Posted by McGXJ
I was looking at this one from JCR- http://www.jcroffroad.com/mm5/mercha...Code=1TNST-OTK
Just need to figure out whether I want to do under / over the knuckle
Just need to figure out whether I want to do under / over the knuckle
☠ CF Sheriff ☠
I was looking at this one from JCR- http://www.jcroffroad.com/mm5/mercha...Code=1TNST-OTK
Just need to figure out whether I want to do under / over the knuckle
Just need to figure out whether I want to do under / over the knuckle
In order for JCRs OTK kit to work, you'd need to raise the trackbar mount on the axle and lower the mount on the frame.
There's only one that i know of that's an OTK tie rod and UTK drag link mount so you don't need to change the trackbar, and that's the IRO OTK kit
☠ CF Sheriff ☠
Senior Member
Join Date: Apr 2012
Location: MARYLAND
Posts: 713
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0L I6
Roger that, thanks for the info!
CF Veteran
Join Date: Jan 2012
Location: Baltimore, MD
Posts: 8,272
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0 I6 HO
i was just at mcdonalds and as i was leaving i noticed the jeep was at about 250*. i figured like the last time i could coast down a big hill and cool off, it worked. but why am i over heating? ive replaced the fan clutch, thermostat, water pump, flushed and cleaned radiator. my dad and i are out of ideas.
CF Veteran
Join Date: Feb 2012
Location: Forest Hill, Maryland
Posts: 6,468
Likes: 0
Received 18 Likes
on
14 Posts
Year: 1998
Model: Cherokee
Engine: 4.0L
Kuzican...it wouldve been nice if you wouldve spoke up about that place sooner as I havr been talking about exhaust for months....
I knew i wasnt getting mandrel bent anymore so for you to offer now Jimmy doesnt really help me.
Look I know i got robbed but everyone makes mistakes. Its done now and Im over it. Next time ill take another route through one of y'all as long as it isnt after the fact...
My buddy whos family owns the shop saw it and was mad they charged me that much so he did give me 150 back under the table...
I knew i wasnt getting mandrel bent anymore so for you to offer now Jimmy doesnt really help me.
Look I know i got robbed but everyone makes mistakes. Its done now and Im over it. Next time ill take another route through one of y'all as long as it isnt after the fact...
My buddy whos family owns the shop saw it and was mad they charged me that much so he did give me 150 back under the table...
CF Veteran
Join Date: Nov 2011
Location: Nashville
Posts: 2,752
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
Here's a thread with some comparision between the IRO and ORO steering kits.
IRO $325~
ORO $600~
http://www.naxja.org/forum/showthread.php?t=1041525
IRO $325~
ORO $600~
http://www.naxja.org/forum/showthread.php?t=1041525