Maryland Cherokee Club
06-12-2013, 09:37 AM
CF Veteran
Join Date: Feb 2012
Location: Laurel, MD
Posts: 2,574
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0L
can you do it for him?
06-12-2013, 09:38 AM
CF Veteran
Join Date: Jan 2012
Location: Baltimore, MD
Posts: 8,272
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0 I6 HO
You have to get them to sk96. Then ill get them to Rob.
if you wheel your jeep **** getting CV joints again When the boots get torn they're shot. Grab some ujoint shafts from an XJ and throw them in so you can change just the joint and they'll hold up to the harsh environment much better.
I have installed several. What's the question?
How the **** do you do it? Lmao. Damien, Rob, and I have no idea what we're doing with his front locker other than to follow the directions.
if you wheel your jeep **** getting CV joints again When the boots get torn they're shot. Grab some ujoint shafts from an XJ and throw them in so you can change just the joint and they'll hold up to the harsh environment much better.
I have installed several. What's the question?
06-12-2013, 09:40 AM
CF Veteran
Join Date: Jan 2012
Location: Baltimore, MD
Posts: 8,272
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0 I6 HO
When I do my axle swap in late december, should I just also install my up country leafs and coils to put me at 3"? I also think want to do a hack 'n' tap with a front drive shaft so that my drive shaft fits and I am positive i wont have vibes.
06-12-2013, 09:41 AM
CF Veteran
Join Date: Feb 2012
Location: Laurel, MD
Posts: 2,574
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0L
06-12-2013, 09:42 AM
CF Veteran
Join Date: Jan 2012
Location: Baltimore, MD
Posts: 8,272
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0 I6 HO
06-12-2013, 09:42 AM
Senior Member
Join Date: Apr 2013
Location: Laurel md
Posts: 719
Likes: 0
Received 0 Likes
on
0 Posts
Model: Cherokee
Whats it look like. My old one is crome in the middle with blade bumpers on the ends. Jw just need to can from my other one since my brother smashed it up in an accident
06-12-2013, 09:44 AM
CF Veteran
Join Date: Nov 2011
Location: Nashville
Posts: 2,752
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0
Got a charcoal grey glove box that opens without dumping all you stuff on the floor?
06-12-2013, 09:50 AM
CF Veteran
Join Date: Mar 2009
Location: Berea, OH
Posts: 7,996
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
TIP: Hold on to the springs....
TIP: Easier to do with the carrier out....
TIP: If you do take the carrier out, MARK the bearing caps with a punch to MAKE SURE you put them back on the SAME way they came off.
Done....
Follow the directions. It is actually very simple.
06-12-2013, 09:51 AM
CF Veteran
Join Date: Mar 2009
Location: Berea, OH
Posts: 7,996
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
No...I think you should tear the Jeep apart twice....WTF kinda question is that?
Also....you have the 242...the H-N-T is the most economical solution.
06-12-2013, 10:06 AM
☠ CF Sheriff ☠
front or rear? I've only done them in the rear, which is pretty easy. I use a set of assorted picks to get everything seated right. Essentially - remove the spiders and thrust washers, install the couplers on each side re-using the thrust washers you just took out. Then insert the spacers (the smooth ring) into each driver with the "open" side pointing in the same direction as the teeth. Slide the first driver into the carrier, aligning the teeth, and push the spacer over as far as you can towards the outside of the carrier. Repeat for other side (the 90° pick tool comes in hand here). Then install the cross pin and the springs + pins as instructed. The cross pin might be a ***** to get in, but keep working at it - everything has to be aligned juuuust right
06-12-2013, 10:12 AM
CF Veteran
Join Date: Dec 2011
Location: Pasadena, MD
Posts: 4,006
Likes: 0
Received 1 Like
on
1 Post
Year: 1987
Model: Wagoneer
Engine: Renix 4.0
Anyone got lower control arms they are looking to get rid of? Dukie, what lca's are you running?
And it feels good to be back on android
And it feels good to be back on android
06-12-2013, 10:26 AM
Seasoned Member
Join Date: Sep 2011
Location: Winchester, VA
Posts: 298
Likes: 0
Received 1 Like
on
1 Post
Year: 2000
Model: Cherokee
Engine: 4.0L I6
06-12-2013, 10:27 AM
CF Veteran
Join Date: Dec 2011
Location: Near the airport by the water
Posts: 1,140
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
Can someone that has had an accident and it's listed on carfax verify whether or not this auto check report is accurate? Mine seems to be fairly accurate but it's missing the report when my bumper had to get replaced from a lady backing into it.
www.geniusvin.com
www.geniusvin.com
06-12-2013, 10:57 AM
Moderator of Jeeps
Join Date: Jul 2011
Location: Frederick, MD from Cleveland, OH
Posts: 21,029
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1993 YJ Wrangler
Engine: 4.0 I6
Finally caught this guy at Wendy's.
Didn't get a chance to say anything, but he was checking out my MJ with the bike in the bed lol
Didn't get a chance to say anything, but he was checking out my MJ with the bike in the bed lol
06-12-2013, 11:11 AM
☠ CF Sheriff ☠