built not bought '89 build
#661
CF Veteran
Joined: Sep 2010
Posts: 4,968
Likes: 0
From: Salt Lake City, UT
Year: 2000
Model: Cherokee
Engine: 4.0L
haha, looks good! You would be amazed at how strong those Rubicon Express stickers are. that winch wont go anywhere! lol (that's actually scary) Looks like a good start though.
Yeah let me know when and I will come help.
Yeah let me know when and I will come help.
#663
CF Veteran
Joined: Sep 2009
Posts: 3,612
Likes: 0
From: West Valley
Year: 1998
Model: Cherokee (XJ)
Engine: 4.0
"new addition" got ya, I'm a little slow. Lol
So the wife got sick of hearing me b**** about working on here POS alero, so she sold it for this, knowing I will have no complaints workin on it...
Attachment 74922
Attachment 74923
That's not the only reason. She loves to wheel, otherwise she would have got a clean little 98 that's better on gas!
Yes that's a winch welded to the factory bumper LMAO some people these days
So the wife got sick of hearing me b**** about working on here POS alero, so she sold it for this, knowing I will have no complaints workin on it...
Attachment 74922
Attachment 74923
That's not the only reason. She loves to wheel, otherwise she would have got a clean little 98 that's better on gas!
Yes that's a winch welded to the factory bumper LMAO some people these days
#668
CF Veteran
Joined: Sep 2010
Posts: 1,649
Likes: 1
From: Springville, UT
Year: 1993
Model: Grand Cherokee
Engine: 5.2 V8, Dual cold air, dual batts, E-fan, Sanden OBA
I don't like it.... I think if your not 100% cool with it then you need to fix it,otherwise it will always bother you.... just my .02
#669
CF Veteran
Joined: Aug 2009
Posts: 1,534
Likes: 0
From: Herriman, Utah
Year: 1994
Model: Cherokee
Engine: 4.0
My corners are similar, only I used tube then plated it. Made the corners quite a bit stronger that way too. I should have narrowed the rear of mine, it looks like it's got a big ol' fat @$$! But i like having plenty of room in the back still for gear, cooler, etc.
Last edited by X1994J; 11-07-2011 at 08:07 AM.
#670
Thread Starter
CF Veteran
Joined: May 2009
Posts: 6,328
Likes: 1
From: SLC, UT
Year: 1989 2 door
Model: Cherokee
Engine: 4.0
Ya I'm not quite 100% on it, but there isn't a whole lot of options to match the top section to the lower bend... It's 16 gate so its hard to work with! I think it looks better in person, & for what the jeeps turning into it works.
As for the bed rails, I'm gonna use the factory inner plastics, & heat up the bend. Then cap off the back, & weld a 3/4" tube along the outside of the pinch weld that bends with the dove. Kinda hard to explain, like Cory's lower hoop that runs along the top of his QP, but with smaller tube.
As for the bed rails, I'm gonna use the factory inner plastics, & heat up the bend. Then cap off the back, & weld a 3/4" tube along the outside of the pinch weld that bends with the dove. Kinda hard to explain, like Cory's lower hoop that runs along the top of his QP, but with smaller tube.
Last edited by builtnotbought89'; 11-07-2011 at 08:31 AM.
#671
CF Veteran
Joined: Dec 2010
Posts: 1,234
Likes: 1
From: Finger Lakes Region NY
Year: 1990
Model: Cherokee
Engine: 4.o
cap the top of it and use the round LED brake and turn signals and I think it'll look awesome. super Beef. also put a MJ tailgate on the back. that be sick.
#672
CF Veteran
Joined: Sep 2010
Posts: 4,968
Likes: 0
From: Salt Lake City, UT
Year: 2000
Model: Cherokee
Engine: 4.0L
#673
Thread Starter
CF Veteran
Joined: May 2009
Posts: 6,328
Likes: 1
From: SLC, UT
Year: 1989 2 door
Model: Cherokee
Engine: 4.0
I'm gonna give it some time, & make the other side the same. Once the tailgate is cut & folded to the same angle as the top half it should flow nicely! Then I'll burn it in permanent. (or tell she goes under the knife again)
Zach ur gonna have to come see it before you hate on it too much lol
Zach ur gonna have to come see it before you hate on it too much lol