Project - "Finally Ours"
#331
Banned
Thread Starter
Join Date: Oct 2009
Location: West Springfield, MA
Posts: 2,231
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0
bedlined the bottoms of my doors and up to where my rear quarter guards will go and re-painted front bumper also ordered bunch of bumpstop stuff...
#338
Banned
Thread Starter
Join Date: Oct 2009
Location: West Springfield, MA
Posts: 2,231
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0
Originally Posted by clayton3854
how do you figure to begin with considering its a 2 door jeep and a 4 door?
#339
Seasoned Member
Join Date: Aug 2011
Location: Agawam, MA
Posts: 406
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Cherokee
Engine: 4.0L I6
Yeah not just vedub kids.... It's everyone... At quick glacé people think its the same jeep lol especially all ur car quest pals
#340
Banned
Thread Starter
Join Date: Oct 2009
Location: West Springfield, MA
Posts: 2,231
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0
bunch of stuff came in mail today
and right now i am currently painting my H.D. Offroad Engineering shackle relocation brackets REV2 and yesterday the yokes required to swap in my NP241OR arrived in the mail from JB-Conversions (i will be writing a installation article since when i decided on the swap i had to do some research so figured ill make it easier)
and right now i am currently painting my H.D. Offroad Engineering shackle relocation brackets REV2 and yesterday the yokes required to swap in my NP241OR arrived in the mail from JB-Conversions (i will be writing a installation article since when i decided on the swap i had to do some research so figured ill make it easier)
#341
Banned
Thread Starter
Join Date: Oct 2009
Location: West Springfield, MA
Posts: 2,231
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0
decided the front extended bumpstops would be to much so i took one prothane insert and cut it in half and put each half in each coil looks like it should work perfectly...now for the hard work tomorrow...also got a tattoo yesterday my first one on the backside of my lower arm:
#342
Senior Member
Join Date: Jan 2010
Location: barnesville pa 18214
Posts: 868
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996 1996 1997
Model: Cherokee
Engine: 4.0L 5.2L
#344
Banned
Thread Starter
Join Date: Oct 2009
Location: West Springfield, MA
Posts: 2,231
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0
got some updates from yesterday not all of them though cause it got to dark for pics but got the rear bump stops all set up with shackle relocation brackets and changed my exhaust up a bit...
lowered rear end to take off shackles and u-bolt plates:
welded on some flat stock to act as a bump stop pad:
while they were cooling down and then paint drying started installed shackle relocation brackets:
then installed u-bolt plates:
then raised up leafs to meet shackle brackets found out my clunk is from a bad shackle bushing cause i couldn't grease them in the factory location:
then set ride height and drilled for the bump stops and installed:
lowered rear end to take off shackles and u-bolt plates:
welded on some flat stock to act as a bump stop pad:
while they were cooling down and then paint drying started installed shackle relocation brackets:
then installed u-bolt plates:
then raised up leafs to meet shackle brackets found out my clunk is from a bad shackle bushing cause i couldn't grease them in the factory location:
then set ride height and drilled for the bump stops and installed:
Last edited by mcguyver_xj; 08-19-2012 at 09:34 AM.