2003 jeep Cherokee transmission problems!!!
#17
#18
Seasoned Member
wrong thread.
WHY are all posts getting magically put into the wrong thread???
I KNOW I posted in "what did you do today"
this morning its in this thread.....
WHY are all posts getting magically put into the wrong thread???
I KNOW I posted in "what did you do today"
this morning its in this thread.....
Last edited by John T; 03-24-2019 at 06:42 AM. Reason: wrong thread
#19
Seasoned Member
hi. I have a 2003 Jeep Grand Cherokee Laredo with about 200,000 miles on it. Today my jeep started up fine. I put it in reverse to leave and it went smoothly but when I shifted to drive it didn't do anything? Some advice would be great, so I could know what I'm looking for or any common troubleshooting I could before I take it to the shop! Please help!
#22
Senior Member
Attachment 301660
Attachment 301661
Attachment 301662
Attachment 301663
Ripped off the Claytons link bridge/truss ...replaced with Artec 14 bolt and made a link bracket and increased vertical separation from under 8 to about 10 then cut some steel and made a link bridge tie to the diff cover the tube us 1.5 .250 wall the mounting tabs are a500 .500 thick plate with a grade 8 1 inch bolt in double shear...single shear rating is 94,000 ;-).
And made about 4 passes around the tubes this plus the diff and pinion ties should prevent spinning a tube. Will be finishing the back brace and pinion tie in next week .
Attachment 301661
Attachment 301662
Attachment 301663
Ripped off the Claytons link bridge/truss ...replaced with Artec 14 bolt and made a link bracket and increased vertical separation from under 8 to about 10 then cut some steel and made a link bridge tie to the diff cover the tube us 1.5 .250 wall the mounting tabs are a500 .500 thick plate with a grade 8 1 inch bolt in double shear...single shear rating is 94,000 ;-).
And made about 4 passes around the tubes this plus the diff and pinion ties should prevent spinning a tube. Will be finishing the back brace and pinion tie in next week .
gesh! I don't think you need to worry about that pumpkin spinning.
#23
Junior Member
Discovered the location of the Maintenance Reminder module under the dash and disconnected it! Reinstalled both front seats and center console. Replaced the trans shift indicator bulb. Did a basic steering toe adjustment so I can drive it to the alignment shop later. Connected and re-installed windshield washer reservoir. Found some more ground connections and refreshed them.
#24
CF Veteran
Join Date: May 2012
Location: Lost in the wilds of Virginia
Posts: 7,964
Received 956 Likes
on
771 Posts
Year: 1998 Classic (I'll get it running soon....) and 02 Grand
Model: Cherokee (XJ)
Engine: 4.0
The good news is, you can turn off that "Related Thread" crap in your profile. I did, and I'm glad I did. If I could nuke it from the site completely, I would.
NOTE TO THE NEXT POSTER! THIS IS A ZOMBIE THREAD! PLEASE LET IT DIE!
NOTE TO THE NEXT POSTER! THIS IS A ZOMBIE THREAD! PLEASE LET IT DIE!
Thread
Thread Starter
Forum
Replies
Last Post
Austen Mack
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
7
08-06-2017 03:55 AM
blueseasons
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
3
03-04-2016 07:38 PM
ducter
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
2
03-02-2016 03:52 PM
steveandtracy7
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
1
03-01-2016 07:19 PM
n6xb
Stock Grand Cherokee Tech. All ZJ/WJ/WK Non-modified/stock questions go here!
3
03-01-2016 06:34 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)