Complete Center Console Overhaul
#1
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
Complete Center Console Overhaul
Alright, so this started out as a simple problem, then grew into an entire thing. I've posted about it before in other threads because it was relevant to what I was doing, but figured I would compile it all together into one thread. Follow me and watch as I completely rethink the pre96 center console!
If you want to read in full detail about individual mods to the center console instead of a glazed over compile of information, you can find them here:
https://www.cherokeeforum.com/f67/mj-parking-brake-pre-96-xj-264354/
https://www.cherokeeforum.com/f67/pre-96-center-console-armrest-modification-263129/
If you want to read in full detail about individual mods to the center console instead of a glazed over compile of information, you can find them here:
https://www.cherokeeforum.com/f67/mj-parking-brake-pre-96-xj-264354/
https://www.cherokeeforum.com/f67/pre-96-center-console-armrest-modification-263129/
Last edited by Travis Mudrich; 08-06-2023 at 12:43 PM. Reason: Typo
#2
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
Armrest Repair (Part 1)
So I'm sure you're aware, these pre96 armrest break right at the post where it attaches to the hinge. I've went through 3 multiple armrests before I figured it out.
The 3 major problems with the design that leads to failure are:
1. The posts that attach to the hinge are nearly not as supported as they need to be.
2. The screws going into the posts are not long enough.
3. Theres excess room around the mounting point allowing for the armrest to shift around.
After replacing the first one, this second one broke too.
You can see here I attempted to support the posts with JBWeld, but it atill broke. The armrest was ripped up anyways.
The 3 major problems with the design that leads to failure are:
1. The posts that attach to the hinge are nearly not as supported as they need to be.
2. The screws going into the posts are not long enough.
3. Theres excess room around the mounting point allowing for the armrest to shift around.
After replacing the first one, this second one broke too.
You can see here I attempted to support the posts with JBWeld, but it atill broke. The armrest was ripped up anyways.
#3
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
Armrest Repair (Part 2)
From there, I got a new armrest.
I took apart the new armrest
Cleaned up all excess expanding foam
100% infill with JB Weld. I contemplated putting some on the otherside but figured this should be enough.
And got proper length screws.
Heres the size difference.
I took apart the new armrest
Cleaned up all excess expanding foam
100% infill with JB Weld. I contemplated putting some on the otherside but figured this should be enough.
And got proper length screws.
Heres the size difference.
#4
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
Armrest Repair (Part 3)
Finally, just had one more thing to do.
I was already this far down the road, figured bight as well do it all.
Filled in the latch also.
Thre it back together with grease
Bolted it back together
Better than factory
I was already this far down the road, figured bight as well do it all.
Filled in the latch also.
Thre it back together with grease
Bolted it back together
Better than factory
The following users liked this post:
ijeeep (04-24-2024)
#5
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
MJ Emergency Brake Swap (Part 1)
I fell into a Comanche E-brake swap. I did this to install cupholders, more center console room, and because I want to be different 😄 Here's what I've got going on.
First, I removed the hand brake
I extended the brake switch line
Crimped on a new end, and rerouted it under the carpet towards the driver side footwell
First, I removed the hand brake
I extended the brake switch line
Crimped on a new end, and rerouted it under the carpet towards the driver side footwell
#7
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
E-Brake Swap (Part 3)
Went over the patch with glazing putty to fill in the gaps. I eventually will go over the whole thing with black textured paint to blend it all together. (I still have to do the cupholders)
First pass
Second pass
First pass
Second pass
Last edited by Travis Mudrich; 08-06-2023 at 01:22 PM. Reason: Typo
Trending Topics
#8
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
Center Console Storage (Part 1)
Because I deleted the E-brake, I now have more room in that area. At first I was after a Tuffy console insert. Those are hard rare now, but I own a spot welder. I highly considered making my own template and putting one together with sheet metal. Pretty simple actually. But instead of rising the top up, I figure I'd bring the bottom down.
This a standard 5.56 ammo can
I removed the hinge
Removed the handle lip
It seats in perfectly
You can see here it drops lower than original.
Don't mind the quality of the ammo can, this one is a beat up prototype. The interior space is almost double! And the bottom of the ammo can will bolt right up to the trans tunnel where the bracket used to sit.
Unfortunately, because it sits low, i will have to delete my rear seat air conditioning. Minor loss for what I am gaining.
This a standard 5.56 ammo can
I removed the hinge
Removed the handle lip
It seats in perfectly
You can see here it drops lower than original.
Don't mind the quality of the ammo can, this one is a beat up prototype. The interior space is almost double! And the bottom of the ammo can will bolt right up to the trans tunnel where the bracket used to sit.
Unfortunately, because it sits low, i will have to delete my rear seat air conditioning. Minor loss for what I am gaining.
#9
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
Lower Air Conditioning (Part 1)
Because I deleted the air-conditioning tube in place of more storage, I was left with a few options. I could just leave it as is. Or I could reroute the air.
I removed the vent from under the climate controls on a spare dash that I had.
And broke off the change cubby that sits under the ashtray.
I shaved off the lip that interfaces with the rest of the black center console insert.
I removed the vent from under the climate controls on a spare dash that I had.
And broke off the change cubby that sits under the ashtray.
I shaved off the lip that interfaces with the rest of the black center console insert.
#10
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
Air Conditioning (Part 2)
I trimmed all of the excess plastic around the vent so it would sit flush
And angled the corners so it would sit inside of the walls
#11
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
Air Conditioning (Part 3)
From here, I needed to pre everything to accept the vent.
I cut a hole in the change cubby
You can start to see here how I will intrigrate it with the air supply.
I cut a hole in the change cubby
You can start to see here how I will intrigrate it with the air supply.
#12
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
Air Conditioning (Part 4)
Nearly done!
Im going to lay the vent on top of the cubby and then lay the console insert over the whole thing.
This is what it will look like.
I still have to JB Weld it all together but I'm waiting to texture paint it first
Im going to lay the vent on top of the cubby and then lay the console insert over the whole thing.
This is what it will look like.
I still have to JB Weld it all together but I'm waiting to texture paint it first
#13
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
What now?
So this is what I still have to do:
1. Insert cupholders where the E-brake used to be
2. Finish the glaze putty
3. Texture paint the whole black insert
4. Attach the vent
5. Connect the vent to the air supply
6. Finalize the design of the interior storage
That's all of the big ticket items. Of course there's a bunch of smaller tasks to do to complete the larger tasks, but you get the idea.
1. Insert cupholders where the E-brake used to be
2. Finish the glaze putty
3. Texture paint the whole black insert
4. Attach the vent
5. Connect the vent to the air supply
6. Finalize the design of the interior storage
That's all of the big ticket items. Of course there's a bunch of smaller tasks to do to complete the larger tasks, but you get the idea.
#14
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
Modifications
The 5 modification this encompasses are:
1. Armrest reinforcement
2. E-brake delete
3. Larger storage capacity
4. Cupholders
5. Air vent reroute
Progress so far 😁😁😁
I hope everyone has enjoyed so far! If you have any questions or comments, feel free to leave them below. I love to hear back from the community.
What other center console mods have you done? I would love to see pictures!
1. Armrest reinforcement
2. E-brake delete
3. Larger storage capacity
4. Cupholders
5. Air vent reroute
Progress so far 😁😁😁
I hope everyone has enjoyed so far! If you have any questions or comments, feel free to leave them below. I love to hear back from the community.
What other center console mods have you done? I would love to see pictures!
The following users liked this post:
ijeeep (04-24-2024)
#15
Seasoned Member
Thread Starter
Join Date: Apr 2021
Posts: 438
Received 88 Likes
on
76 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: 4.0 High Output
E-Brake Swap (Part 4)
Made some progress today!
Sanded the whole thing down to 180 grit. I was going to do textured paint but figured I wouldnt be happy with it. I think the texture would be too large and it would remind me more of bedliner rather than what was originally on there. So I opted out for a smooth look since the texture is pretty subtle already.
Go the bondo sanded down to clean lines
Hit it with some black spray paint to see the imperfections. After sanding it down to see where the two panels meet, I realised I made a mistake. The bondo sands quicker than the plastic (Duh!) So now parts of the bondo are lower. It's fine, just means I have to do more work.
After I get this patch panel how I like it, I'll probably go over the whole thing again up to 220 grit. I want this thing as smooth as glass. I am going to try to find a flat black to help match how it was originally.
Still trying to figure out the cupholders. I have the OEM one that clicks into the side. I doubt I'll ever use it again because I hate how much if the passenger side leg room it takes, even though I think it's a considerably better option than the ebrake style one. There are so many issues with that I'm not even going to go into detail. Either way, I think the OEM is worth more to someone else than for me to patch in. Not sure what I'm going to do yet.
Since I'm patching this together and refinishing it, i think i may pay a visit to the junkyard to see what other cupholder I can find and what other center console goodies are out there in other trucks. I'm do mind modifying my XJ, but I want it to appear stock.
For example, I don't really like the little change holder between the E-Brake and the transmission shifter. It's was a great attempt by Chrystler to utilize some wasted space, but I bet I can find something better to put there. We'll see!
Sanded the whole thing down to 180 grit. I was going to do textured paint but figured I wouldnt be happy with it. I think the texture would be too large and it would remind me more of bedliner rather than what was originally on there. So I opted out for a smooth look since the texture is pretty subtle already.
Go the bondo sanded down to clean lines
Hit it with some black spray paint to see the imperfections. After sanding it down to see where the two panels meet, I realised I made a mistake. The bondo sands quicker than the plastic (Duh!) So now parts of the bondo are lower. It's fine, just means I have to do more work.
After I get this patch panel how I like it, I'll probably go over the whole thing again up to 220 grit. I want this thing as smooth as glass. I am going to try to find a flat black to help match how it was originally.
Still trying to figure out the cupholders. I have the OEM one that clicks into the side. I doubt I'll ever use it again because I hate how much if the passenger side leg room it takes, even though I think it's a considerably better option than the ebrake style one. There are so many issues with that I'm not even going to go into detail. Either way, I think the OEM is worth more to someone else than for me to patch in. Not sure what I'm going to do yet.
Since I'm patching this together and refinishing it, i think i may pay a visit to the junkyard to see what other cupholder I can find and what other center console goodies are out there in other trucks. I'm do mind modifying my XJ, but I want it to appear stock.
For example, I don't really like the little change holder between the E-Brake and the transmission shifter. It's was a great attempt by Chrystler to utilize some wasted space, but I bet I can find something better to put there. We'll see!