Homebrew Jeep Mods
#454
Senior Member
Join Date: May 2010
Location: Here, There, Everywhere
Posts: 745
Likes: 0
Received 1 Like
on
1 Post
Year: 1997
Model: Grand Cherokee
Engine: 5.2
here are my home made disco's made with a 1/2" clevis pin on the bottom and 7/16? wing nuts and lock washers. they work awesome then i use a 2' piece of velcro to hold up the sway bar so its not flopping around
#455
Member
Join Date: Jun 2010
Location: Eugene, Oregon
Posts: 160
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0 L I6 (Ford 4.2L Injector Upgrade and Yellow Top Optima))
Nice, how much was that wing nut 4 bucks at least.... isn't 1/2 clevis pin a little loose in the sway bar bushing? Good idea though, hate to see people blow over a hundred dollers on discos... Did you spray paint your bumpstop red? intresting.
#456
Senior Member
Join Date: May 2010
Location: Here, There, Everywhere
Posts: 745
Likes: 0
Received 1 Like
on
1 Post
Year: 1997
Model: Grand Cherokee
Engine: 5.2
not $4 they were $1.39 at ace. the pin is a little loose but not bad to were it would break because of it. i used some washers in there also to tighten it up. i didnt paint my bumpstop it was like that when i bought it. its all scratched and stuff cuz i used a 2lb sledge to get my spacer in and missed a couple times lol.
#457
CF Veteran
Join Date: Dec 2009
Location: Harleysville, PA
Posts: 2,091
Likes: 0
Received 1 Like
on
1 Post
Year: 1998
Model: Cherokee
Engine: 4.0L I6 Powertech
Ok here is my write up on the switch panel for you guys.
http://www.jeepforum.com/forum/f177/...l-idea-926047/
As far as the LED lighting I just replaced all the fractory bulbs with LED's
http://www.jeepforum.com/forum/f177/...l-idea-926047/
As far as the LED lighting I just replaced all the fractory bulbs with LED's
#459
Seasoned Member
Join Date: Jul 2009
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0L HO
This is where you tap in too.
These are the LED's I used. I used 3mm LED's
http://www.oznium.com/prewired-leds
#461
Seasoned Member
Join Date: Jul 2009
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0L HO
I got a 1/8" drill bit. Drilled the hole. Then I put a medium wendys cup in mine. Which fits really tight in the holder. I then placed a piece of tape on the cup where the hole was (so the super glue won't peal the paper off the cup). I then held the LED's in place and super glued them in.
#465
aka Wade-O
Join Date: Dec 2008
Location: IN
Posts: 3,703
Likes: 0
Received 10 Likes
on
9 Posts
Year: 1989 Comanche
Model: Cherokee
Engine: 4.0
this is gonna take a while....
front bumper
rear bumper
long arms
adjustable bumpstops
tracbar, tracbar axle mount, tracbar frame mount brace
spare tire mount
shock adapters
rock rails
half doors
hi-lift mount
front bumper
rear bumper
long arms
adjustable bumpstops
tracbar, tracbar axle mount, tracbar frame mount brace
spare tire mount
shock adapters
rock rails
half doors
hi-lift mount