Welding thread!!!!
#1036
Seasoned Member
Join Date: Mar 2015
Location: Portland, OR
Posts: 280
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0L
I thought you were meaning over lapping spot welds or pulsed mig. It's how about 80% of WRC cages are built now and days. I'm familiar with the technique you're using (half moon, C's, ect).
#1037
Member
Join Date: Jul 2012
Location: Buckeye AZ
Posts: 140
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0
I use a cursive lower case "e" type motion to get the stacked look. A lot of people trigger weld. or spot weld on top of spot weld.. The chick on extreme 4x4 was demonstrating the trigger technique a few years ago. lol
#1040
Member
Join Date: Jul 2012
Location: Buckeye AZ
Posts: 140
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0
Thanx.. This pic is about twice as big as the actual part. It actually looked better in person since the pic is such a close up.. @ least its way bigger on my pc.. lol
#1042
Member
Join Date: Jul 2012
Location: Buckeye AZ
Posts: 140
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0
Here's is the front section of frame stiffeners that I make for ZJ .. The customer installed the full set front to rear. Lots of welding here. Some decent welds too.
#1044
Banned
Join Date: Oct 2014
Location: tucson
Posts: 17
Likes: 0
Received 9 Likes
on
9 Posts
Year: 1992
Model: Cherokee
Engine: 4.0
Did my first big welding job today. I know its ugly but its a start. Tomorrow I'll add another tube and make some mounting brackets as the stock ones aren't worth a ****
#1045
Member
Join Date: Jul 2012
Location: Buckeye AZ
Posts: 140
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0
#1046
::CF Administrator::
For sure, the best teacher is time under the hood. BTW 93, I sent you a PM...I'll get some pics of my bumper for ya this weekend...keep in mind I have a bender, so my end result will be different from yours, but I'll try to help you out with some pics so you can see what I did, and what you might be able to work into your build.
#1047
::CF Administrator::
A couple of pics from work today. Keep in mind, I'm welding with an injured hand at the moment...not too bad. Just welded a backing plate on some 8" C-channel, 3/8" thick, for a drainage system on a piece of equipment. The second pic is a small 1 1/2" kicker, to help the water flow into the sump tank better, that weld isn't as clean, I got interrupted, and had to restart towards the middle, got a tad fat there, LOL
Done with a Miller 252 with .035 wire...love that machine
Done with a Miller 252 with .035 wire...love that machine
Last edited by Rogue4x4; 04-17-2015 at 11:58 PM.
#1049
Banned
Join Date: Oct 2014
Location: tucson
Posts: 17
Likes: 0
Received 9 Likes
on
9 Posts
Year: 1992
Model: Cherokee
Engine: 4.0
Also, I made the sides so long on the bumper because eventually I am going to make tube fenders and tie everything together. Weld the tube fenders to the rock sliders and eventually make a full exo cage
#1050
No, I don't lick fish.