Driver side ball joints
#1
Junior Member
Thread Starter
Join Date: Oct 2015
Location: Northern Va
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0l
Driver side ball joints
The driver side ball joints on xj are bad and need to be replaced. The shop I took it to quoted me $459 for the parts and labor and also comes with a lifetime warranty on the parts and labor. Is this reasonable?
#2
Member
Join Date: Oct 2012
Location: Thornton, CO
Posts: 140
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1997
Engine: 4.0L
If you have any mechanical background, do it yourself or find some people to help you. The balljoints are around $30/ea and you can rent a tool from the autoparts store. Save yourself $400 that way
#3
Junior Member
Thread Starter
Join Date: Oct 2015
Location: Northern Va
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0l
My dad usually helps me with this but does not have time anytime in the near future.
#5
Senior Member
i did my drivers side 2yrs ago...not complex....watch several youtubes, everyone does something different, can pick stuff up by watching
#6
Junior Member
Thread Starter
Join Date: Oct 2015
Location: Northern Va
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0l
#7
Junior Member
Thread Starter
Join Date: Oct 2015
Location: Northern Va
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0l
I've done the Ujoints on the jeep before. But never have done ball joints. From what I understand ball joints have more involved and require lots of beating lol
Trending Topics
#8
Senior Member
set of moog upper and lower one side is $80 on amazon....
ive seen ppl say its 1.8hrs book time per side, no idea if true
and labor rates are different in different areas
probably took me 5hrs to do one side....walking away and swearing alot, did it in my snowy driveway
i have the parts to do the other side, doesnt NEED it yet...im sure i can do it in 3 hrs now....no air tools
#9
Senior Member
#10
Seasoned Member
Join Date: Jul 2014
Location: Albuquerque
Posts: 389
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L Inline 6
Watch
-
Then got Autozone or the like and rent the press.
Getting them OUT is the PITA - Going in is relatively easy.
Synergy's will set you back about $125 a piece, but unless you are wheeling it, probably don't need to go that high end.
Then got Autozone or the like and rent the press.
Getting them OUT is the PITA - Going in is relatively easy.
Synergy's will set you back about $125 a piece, but unless you are wheeling it, probably don't need to go that high end.
#11
Seasoned Member
Join Date: Oct 2013
Location: Idaho
Posts: 376
Likes: 0
Received 4 Likes
on
3 Posts
Year: 1991
Model: Cherokee
Engine: 4.0 Liter
I just did all my ball joints not too long ago. It's definitely not hard at all. You're gonna want Dana/Spicer ball joints, they're about $50 a set on amazon. The press, adapter set, and axle nut socket were $220 something rented. It was my first time and it took me maybe 4 hours taking my time and doing it right.
#12
Seasoned Member
Join Date: Dec 2012
Location: Indiana
Posts: 340
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
I just did all my ball joints not too long ago. It's definitely not hard at all. You're gonna want Dana/Spicer ball joints, they're about $50 a set on amazon. The press, adapter set, and axle nut socket were $220 something rented. It was my first time and it took me maybe 4 hours taking my time and doing it right.
When I changed them out on my XJ (they looked to be original Spicers at 150,000 miles), they would not budge and were completely seized to the axle. Even after soaking in Kroil for two weeks and using heat, they wouldn't move. I finally got pissed and used a 4 ft. pipe/breaker bar on the ball joint press, but only managed to bend the press and still not move the joint. To get them out, I ended up cutting the joints flush with the knuckle, drilling/knocking out the stud, and then used an air chisel to collapse and drive out the "sleeve" that remained. Odds are that you would have an easier time, but be prepared for "issues".
#13
Junior Member
Thread Starter
Join Date: Oct 2015
Location: Northern Va
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0l
It's not hard, but be prepared for the worst. I've swapped them before where you could almost knock them out with a hammer, but it usually doesn't go that easy. When I changed them out on my XJ (they looked to be original Spicers at 150,000 miles), they would not budge and were completely seized to the axle. Even after soaking in Kroil for two weeks and using heat, they wouldn't move. I finally got pissed and used a 4 ft. pipe/breaker bar on the ball joint press, but only managed to bend the press and still not move the joint. To get them out, I ended up cutting the joints flush with the knuckle, drilling/knocking out the stud, and then used an air chisel to collapse and drive out the "sleeve" that remained. Odds are that you would have an easier time, but be prepared for "issues".
#14
Senior Member
It's not hard, but be prepared for the worst. I've swapped them before where you could almost knock them out with a hammer, but it usually doesn't go that easy.
When I changed them out on my XJ (they looked to be original Spicers at 150,000 miles), they would not budge and were completely seized to the axle. Even after soaking in Kroil for two weeks and using heat, they wouldn't move. I finally got pissed and used a 4 ft. pipe/breaker bar on the ball joint press, but only managed to bend the press and still not move the joint. To get them out, I ended up cutting the joints flush with the knuckle, drilling/knocking out the stud, and then used an air chisel to collapse and drive out the "sleeve" that remained. Odds are that you would have an easier time, but be prepared for "issues".
When I changed them out on my XJ (they looked to be original Spicers at 150,000 miles), they would not budge and were completely seized to the axle. Even after soaking in Kroil for two weeks and using heat, they wouldn't move. I finally got pissed and used a 4 ft. pipe/breaker bar on the ball joint press, but only managed to bend the press and still not move the joint. To get them out, I ended up cutting the joints flush with the knuckle, drilling/knocking out the stud, and then used an air chisel to collapse and drive out the "sleeve" that remained. Odds are that you would have an easier time, but be prepared for "issues".
#15
CF Veteran
now go buy yourself a cheap press, maybe step up to a cheap kit from amazon or harbor freight and go at it yourself.
i like to use my 7.5a electric impact gun to tighten the press, then my bfh to hammer the end once under load and bobs your uncle.
i have had to use washers and kinda stack them under the press cup to get it to sit properly on the knuckle as i didn't have any angled cups.