Opinions on this Truck
#1
Senior Member
Thread Starter
Join Date: Apr 2009
Location: Grand Haven, Michigan
Posts: 922
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998, 1999
Model: Cherokee
Engine: 4.0
Opinions on this Truck
I found this 1978 F250 today. It was owned by the Fire Department for most of it's life. They had a big water tank on the back so the current Owner put a beat up box on the back. The truck has 68,000 original miles on it. I believe it has Dana 60 axels front and rear. Or maybe a Dana 44HD in front... I can see the rear is a full floater. Would these Dana's work on a Cherokee build? Or are they too heavy and overkill?
I don't know if I'd have them shortened or use big flares...
The truck has a 4 speed. I have the VIN does anyone know where I could run it online to find out more info? If not I guess I will call the Dealer tomorrow. Hopefully they go back to 1978.
It has the less desireable 400 M motor. It starts and runs fine. I'm still negotiating on the price.
Thanks
Mike
I don't know if I'd have them shortened or use big flares...
The truck has a 4 speed. I have the VIN does anyone know where I could run it online to find out more info? If not I guess I will call the Dealer tomorrow. Hopefully they go back to 1978.
It has the less desireable 400 M motor. It starts and runs fine. I'm still negotiating on the price.
Thanks
Mike
Last edited by Mike1998XJ; 07-17-2009 at 01:56 AM.
#4
Senior Member
Thread Starter
Join Date: Apr 2009
Location: Grand Haven, Michigan
Posts: 922
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998, 1999
Model: Cherokee
Engine: 4.0
What do you suppose it's worth? I have a Diesel Tractor to plow with so I could sell the plow and salter. I wonder What I could get for them? The Guy said he was thinking about asking $2000 for the Truck.
Thanks
Mike
Thanks
Mike
#5
Senior Member
Thread Starter
Join Date: Apr 2009
Location: Grand Haven, Michigan
Posts: 922
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998, 1999
Model: Cherokee
Engine: 4.0
I could sell the plow motor and salt spreader and end up with the axels for pretty cheap? They look real heavy... Maybe I wouldn't be able to move with them on!
Thanks
Mike
#6
CF Veteran
Join Date: Feb 2009
Location: socal
Posts: 7,244
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
i am cheep so i would offer like 1200 to 1500 but that's me and it looks to be in ok shape with low miles so 2000 may not be to bad
#7
CF Veteran
Join Date: Feb 2009
Location: socal
Posts: 7,244
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
i have seen a lot of builds using ford Dana 60 but i am unsure of the year they are from but anything can be made to work with enough time and money or work
Trending Topics
#8
Senior Member
Thread Starter
Join Date: Apr 2009
Location: Grand Haven, Michigan
Posts: 922
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998, 1999
Model: Cherokee
Engine: 4.0
Has anyone put those Dana 60's under their Cherokee?
Mike
#9
CF Veteran
Join Date: Feb 2009
Location: socal
Posts: 7,244
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
take a look at this build i think he is doing the swap with the axles from this kinda truck.
https://www.cherokeeforum.com/f46/project-wreck-rocks-19942/
https://www.cherokeeforum.com/f46/project-wreck-rocks-19942/
#11
Member
Join Date: Jul 2009
Posts: 200
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0L
You need to get a measurement of the diameter of the lock out... or of the diameter of the front axle tube.
Most fords of that era especially the 250's had d60 rear.... If the front end has king pins, and the hubs are like 4" it's a D-60
Here is an interesting read for ya'!
http://www.pirate4x4.com/tech/billav...ont/index.html
It has pictures and tells you how to identify the axle under various models of trucks... IIf you get the BOM number you can go to DANA's website and enter it and it will tell you what the axle came out of.
Most fords of that era especially the 250's had d60 rear.... If the front end has king pins, and the hubs are like 4" it's a D-60
Here is an interesting read for ya'!
http://www.pirate4x4.com/tech/billav...ont/index.html
It has pictures and tells you how to identify the axle under various models of trucks... IIf you get the BOM number you can go to DANA's website and enter it and it will tell you what the axle came out of.
#12
Senior Member
Thread Starter
Join Date: Apr 2009
Location: Grand Haven, Michigan
Posts: 922
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998, 1999
Model: Cherokee
Engine: 4.0
You need to get a measurement of the diameter of the lock out... or of the diameter of the front axle tube.
Most fords of that era especially the 250's had d60 rear.... If the front end has king pins, and the hubs are like 4" it's a D-60
Here is an interesting read for ya'!
http://www.pirate4x4.com/tech/billav...ont/index.html
It has pictures and tells you how to identify the axle under various models of trucks... IIf you get the BOM number you can go to DANA's website and enter it and it will tell you what the axle came out of.
Most fords of that era especially the 250's had d60 rear.... If the front end has king pins, and the hubs are like 4" it's a D-60
Here is an interesting read for ya'!
http://www.pirate4x4.com/tech/billav...ont/index.html
It has pictures and tells you how to identify the axle under various models of trucks... IIf you get the BOM number you can go to DANA's website and enter it and it will tell you what the axle came out of.
Thanks
Mike
#13
CF Veteran
that is the good year for ford axles. 78-79 should have d44HD hp flat top front with ball joints and big brakes with a d60 rear.
you'd have to machine a bit of the leaf spring perch from the front axle as it's cast into the pumpkin, but you can weld on control arm mounts and coil buckets easy enough.
as for the rear, you just remove the leaf spring perches and weld on new ones in the correct spot.
it would take a bit of work, but very doable.
only thing is, you'd need 8 bolt 16.5 inch rims to clear those brakes.
i was gonna go with those exact same axles, but figured for the wheeling i do, those would be too big and heavy. so i went with 79 bronco d44/9".
here, those same axles go for 600 bux for the set.
you'd have to machine a bit of the leaf spring perch from the front axle as it's cast into the pumpkin, but you can weld on control arm mounts and coil buckets easy enough.
as for the rear, you just remove the leaf spring perches and weld on new ones in the correct spot.
it would take a bit of work, but very doable.
only thing is, you'd need 8 bolt 16.5 inch rims to clear those brakes.
i was gonna go with those exact same axles, but figured for the wheeling i do, those would be too big and heavy. so i went with 79 bronco d44/9".
here, those same axles go for 600 bux for the set.
#14
Senior Member
Thread Starter
Join Date: Apr 2009
Location: Grand Haven, Michigan
Posts: 922
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1998, 1999
Model: Cherokee
Engine: 4.0
that is the good year for ford axles. 78-79 should have d44HD hp flat top front with ball joints and big brakes with a d60 rear.
you'd have to machine a bit of the leaf spring perch from the front axle as it's cast into the pumpkin, but you can weld on control arm mounts and coil buckets easy enough.
as for the rear, you just remove the leaf spring perches and weld on new ones in the correct spot.
it would take a bit of work, but very doable.
only thing is, you'd need 8 bolt 16.5 inch rims to clear those brakes.
i was gonna go with those exact same axles, but figured for the wheeling i do, those would be too big and heavy. so i went with 79 bronco d44/9".
here, those same axles go for 600 bux for the set.
you'd have to machine a bit of the leaf spring perch from the front axle as it's cast into the pumpkin, but you can weld on control arm mounts and coil buckets easy enough.
as for the rear, you just remove the leaf spring perches and weld on new ones in the correct spot.
it would take a bit of work, but very doable.
only thing is, you'd need 8 bolt 16.5 inch rims to clear those brakes.
i was gonna go with those exact same axles, but figured for the wheeling i do, those would be too big and heavy. so i went with 79 bronco d44/9".
here, those same axles go for 600 bux for the set.
The Ford Dealer couldn't run the VIN. Too old they said. I'll have to go back and look at it if it's worth it. I guess if I could get the whole truck for $1000 and parts the rest of it out that might be ok.
#15
CF Veteran
Mike
Since this is a 3/4 ton, it is most likely that the front is a D44 with heavy tubes and 3/4 ton outers. If you are going to use this equipment in your XJ, there are a few things you need to ask yourself. Like what am I going to do with this XJ? If the answer doesn't involve rock crawling, I would suggest going with the 1/2 ton running gear instead. That D60 weigh a ton and that pumpkin hangs down a long ways and will hang up on everything. The 9" rear end can be made just as strong, and in fact has a stronger ring and pinion with half the weight and much better ground clearance.
Since this is a 3/4 ton, it is most likely that the front is a D44 with heavy tubes and 3/4 ton outers. If you are going to use this equipment in your XJ, there are a few things you need to ask yourself. Like what am I going to do with this XJ? If the answer doesn't involve rock crawling, I would suggest going with the 1/2 ton running gear instead. That D60 weigh a ton and that pumpkin hangs down a long ways and will hang up on everything. The 9" rear end can be made just as strong, and in fact has a stronger ring and pinion with half the weight and much better ground clearance.