What did you do to your Cherokee today?
07-17-2011, 02:01 AM
Member
Join Date: Jan 2011
Location: DuBois, PA
Posts: 219
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
painted my valve cover, but it randomly lost oil pressure, it would 60 easy, now at idle its almost zero, rev it up and gets a little over ten
07-17-2011, 02:07 AM
Seasoned Member
Join Date: Jun 2011
Location: Washington
Posts: 276
Likes: 0
Received 1 Like
on
1 Post
Year: 2000
Model: Cherokee
Engine: 4.0
07-17-2011, 10:02 AM
CF Veteran
Join Date: Jun 2011
Location: Alabama
Posts: 4,618
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: I6
Spent 100 bucks at walmart for it. Than turned a 20 dollar oil change into an 80 dollar change cause my oil pressure sensor broke after I had changed oil so it all shot out, thank god for cat litter
07-17-2011, 10:06 AM
Senior Member
Join Date: Jan 2010
Location: LARRYVILLE
Posts: 602
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1998
Model: Cherokee
Engine: 4.0
Put clear fingernail polish over newly cut fender edges. Next is black door trim and gluing it with auto/marine sealer.
Sent from my iPhone because web wheeling is cheaper...
Sent from my iPhone because web wheeling is cheaper...
07-17-2011, 04:03 PM
Senior Member
Join Date: May 2011
Location: Metro Detroit
Posts: 590
Likes: 0
Received 1 Like
on
1 Post
Year: 1993
Model: Cherokee
Engine: 4.7 Hesco stroker
New BDS 2"lift shocks up front and replaced the nasty, rotted, factory coil isolators with BDS 1.5" coil isolators. It was a pain because the PO must have used what ever he had lying around for hardware when he installed the overpriced Edelbrock shocks that were in there. Some parts were brass, some stainless, some grade 8.....what a nightmare! I'm surprised I have knuckles left......
07-17-2011, 04:24 PM
Seasoned Member
Join Date: Jan 2011
Location: Sacramento, CA
Posts: 430
Likes: 0
Received 2 Likes
on
2 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
Finally finished transferring all the parts from my totaled Cherokee to my new Cherokee. Glad to finally be back in a Jeep
07-17-2011, 04:56 PM
Former Sponsor
Join Date: Jul 2010
Location: Lyons, Colorado
Posts: 1,022
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1992
Model: Cherokee
Engine: 4.0
07-17-2011, 05:26 PM
CF Veteran
Join Date: Sep 2010
Location: Mercer County, NJ
Posts: 12,692
Likes: 0
Received 4 Likes
on
4 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L I6 HO
It was to sunny today to do too much. Filled my washer fluid. Tried to get to dents out but didn't last long in sun so I said fudge it. My neighbor came over to me and asked what I used in my rig the other day and I told him I'll help him seafoam his Santa fe. 
he use to drive an xj until the tranny crapped out.
he use to drive an xj until the tranny crapped out.
07-17-2011, 05:52 PM
CF Veteran
Join Date: Dec 2010
Location: Frederick, Maryland
Posts: 6,880
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0 I-6 High output
It was to sunny today to do too much. Filled my washer fluid. Tried to get to dents out but didn't last long in sun so I said fudge it. My neighbor came over to me and asked what I used in my rig the other day and I told him I'll help him seafoam his Santa fe. he use to drive an xj until the tranny crapped out.
he use to drive an xj until the tranny crapped out.
07-17-2011, 06:25 PM
Newbie
Join Date: Apr 2011
Location: Anna, Tx
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
Reinforced my track bar axle mount. Teaching my daughter to weld and let her weld it up. I need to clean it up a little, but it holds good.
07-17-2011, 06:25 PM
Seasoned Member
Join Date: Jun 2011
Location: Garden Prairie
Posts: 281
Likes: 0
Received 1 Like
on
1 Post
Year: 2000, (1957 Willys)
Model: Cherokee
Engine: 4.0L
Tried to track down a decent hood. Wife drove off the other day with the hood popped. You don't go far like that.
