What did you do to your Cherokee today?
#3676
Senior Member
Join Date: Apr 2009
Posts: 501
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L I-6
I have a 3'' lift on my 2000 XJ, and about a month after i had been driving it the bolt that holds the track bar to the axle side wollowed out the hole and backed off the nut... I then realized that i needed a relocation bracket or an adjusteable track bar, and being a little short on money at the time i choose the relocation bracket (axle side )... However, I'm not satisfied with it and want to run an adjustable bar now....
so my question is can i leave the relocation bracket and add the adjustable track bar, or do i have to remove the relocation bracket.... Thanks.
so my question is can i leave the relocation bracket and add the adjustable track bar, or do i have to remove the relocation bracket.... Thanks.
Also if you want more people to look at, and answer your question, its best to start your own thread here: https://www.cherokeeforum.com/f2/
#3677
Senior Member
Join Date: Dec 2008
Location: northwest Indiana USA
Posts: 606
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990 laredo
Model: Cherokee
mine became a storage vessel for the time being. Threw a transmission in the back, some other BS parts in the back seat and then pushed it behind my friends shop in the weeds with a forklift. Might part it out. Might put a new engine in it. Might just forget about it - dunno.
glad to have a car to drive again- currently getting almost 30mpg out of a 2.8 straight 6.
glad to have a car to drive again- currently getting almost 30mpg out of a 2.8 straight 6.
#3678
Seasoned Member
Join Date: Oct 2008
Location: southern maine
Posts: 466
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1999
Model: Cherokee
Engine: 4.0
took her swimming, got the water out of the engine, checked the oil everything was good. Didn't think about getting water in the tranny fluid. so it boiled out of the dipstick carrying some tranny fluid with it and onto the exhaust.
someone told me my jeep was on fire at an intersection so i pulled over and trew sand at it untill it went out. Then did an "emergency" tranny fluid change after the fire department showed up and laughed at me.
currently looking for deals on a sub amp, cb, i podsand cell phone to replace the items that didn't appreciate being washed.
someone told me my jeep was on fire at an intersection so i pulled over and trew sand at it untill it went out. Then did an "emergency" tranny fluid change after the fire department showed up and laughed at me.
currently looking for deals on a sub amp, cb, i podsand cell phone to replace the items that didn't appreciate being washed.
#3679
CF Veteran
Join Date: Apr 2008
Location: Lakewood, Colorado
Posts: 1,052
Likes: 0
Received 2 Likes
on
2 Posts
Year: 1990 2dr base
Model: Cherokee
Engine: 4.0L
Went wheeling over the weekend and was playing in the rocks, heard a loud pop from the front axle, and now I have no power to the front wheels. Made it very difficult to get out of there with just 2 wheel drive.
#3681
Newbie
Join Date: May 2009
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Cherokee
Engine: 4.0 HO
ok. the last 6 days
Well this is not just today, it's the last 6 days. Replaced belt, upper rad hose, both heater hoses, spark plugs, wires, cap, rotor, valve cover gasket, fr, an rear dif fluids, trans fluid, fitted hood vents, and ram air scoop w/home made brackets, and lower cover for fully functional ram air. picked up more sheet metal to finish off floor boards. currently packing up to head down to Ohio (sw near Kentucky border) to visit my dad, and do some off roading. I'll finish off floor pan,, and paint while I'm down there, I'll post pics when I return.
#3682
CF Veteran
Join Date: Feb 2009
Location: socal
Posts: 7,244
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
#3683
I did that a while back...
EDIT: Here's my build thread and sorry for cross linking...
http://www.cherokeetalk.com/forum/f2...g-xj-35s-3392/
Last edited by Chili Palmer; 06-15-2009 at 04:17 PM.
#3685
Seasoned Member
Join Date: May 2009
Location: Pittsburgh, PA
Posts: 473
Likes: 0
Received 1 Like
on
1 Post
Year: 1990
Model: Comanche (MJ)
Engine: 4.0L
Got a CEL... went to Advanced and used their scanner (for Free which i was pumped about) CEL turned out to state im a dumbass and cant tighten the gas cap correctly lol
#3686
Senior Member
Join Date: Dec 2008
Location: northwest Indiana USA
Posts: 606
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1990 laredo
Model: Cherokee
sold it to a co-worker for 250 bucks, giving him the title for it tomorrow.
kinda sad to see it go but I will get another one, they are a dime a dozen around here.
normally my vehicles go to the junk yard when I get rid of them. This one stood up to my abuse and neglect well- can't knock the jeep for that. they are good trucks.
kinda sad to see it go but I will get another one, they are a dime a dozen around here.
normally my vehicles go to the junk yard when I get rid of them. This one stood up to my abuse and neglect well- can't knock the jeep for that. they are good trucks.
#3687
CF Veteran
When I started my Jeep today, my gauges were not working. I turned it off, then on again, same problem. So I turned it off, and pushed all my fuses to make sure none were loose, turns out that one was, and that was the problem. I wish all problems were this easy to fix.
#3688
Newbie
Join Date: Jun 2009
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0
When I started my Jeep today, my gauges were not working. I turned it off, then on again, same problem. So I turned it off, and pushed all my fuses to make sure none were loose, turns out that one was, and that was the problem. I wish all problems were this easy to fix.