What did you do to your Cherokee today?
#6901
Senior Member
Join Date: Mar 2009
Location: Levittown P.A.
Posts: 818
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1992
Model: Cherokee
Engine: 4.0L H/O
#6902
CF Veteran
Join Date: Jan 2010
Location: Coeur d' Alene, Idaho
Posts: 1,316
Likes: 0
Received 1 Like
on
1 Post
Year: 1998
Model: Cherokee
Engine: 4.0 rebuilt w/ bored TB, banks header, upgraded ignition, 3 row rad, high flow h2o pump, 180* t-stat
installed my Rock Shifter, which is BadAzz by the way, and got my shift rail and and switches from RADesignsproducts.com.
Rory is an awesome dude and a great guy to deal with, he GAVE me a Rock shifter! Just so he could make sure the install in the newer XJ went smooth as butter.
Rory is an awesome dude and a great guy to deal with, he GAVE me a Rock shifter! Just so he could make sure the install in the newer XJ went smooth as butter.
#6903
CF Veteran
Join Date: Feb 2010
Location: Oroville, CA
Posts: 12,367
Likes: 0
Received 22 Likes
on
21 Posts
Year: 1995
Model: Grand Cherokee
Engine: 4.0 with all of the noise and clatter
Installed some Polk Audio tweeters, and replaced the front lower control arms. no more goofy front end antics.
#6904
CF Veteran
Join Date: Feb 2010
Location: Soddy Daisy TN
Posts: 5,420
Likes: 0
Received 0 Likes
on
0 Posts
Year: 97
Model: Cherokee
Engine: 4.0L
Fixed front brakes agaiin, dang Ford and their stupid design on one ton calipers. Welded tubes on front axle and cleaned it out for the riding this weekend.
#6905
started the build on my front bumper. Gosh darn I need a plasma cutter. Using a circular saw to cut 1/4" plate takes way way wayyyyyy to long.
Oh and I managed to warp the 33" long piece of 1/4" that is going to be my winch plate so I had to put it between two spare LCAs I had laying around and jump on it till it was square again. Given I'm learning lots and lots and lots and having a blast. Its just taking way longer than I'd like. Anyone wanna lend me a plasma cutter?
Oh and I managed to warp the 33" long piece of 1/4" that is going to be my winch plate so I had to put it between two spare LCAs I had laying around and jump on it till it was square again. Given I'm learning lots and lots and lots and having a blast. Its just taking way longer than I'd like. Anyone wanna lend me a plasma cutter?
#6906
Bought a new welder from northern tool,welded muffler pipe on jeep,also bought new electric a/c fan,jeep was overheating too much when I was running a/c.Also had to replace front wheel hubs a few months ago
#6907
Seasoned Member
Join Date: Mar 2010
Location: North, Ga
Posts: 388
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Grand Cherokee
Engine: 4.0
I'm in the same boat. But all I have is a pneumatic cut off wheel. So I can cut for about 10min then have to wait for the compressor to refill.
#6908
Junior Member
Join Date: Jul 2010
Location: Colorado Springs Co.
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1992
Model: Cherokee
Engine: 4.0 IL 6
turned my a/c pump in to a compresor to fill a tank, so i can run numatic tools and air back up to drive home.
#6909
CF Veteran
Join Date: Sep 2009
Location: West Valley
Posts: 3,612
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1998
Model: Cherokee (XJ)
Engine: 4.0
Changed out my worn out motor mounts (drivers side was trashed), which cut down on a lot of the vibration I was getting. After changing the mounts my once in a while sound it was making in reverse became an everytime occurence, with the help of my son, he discovered that as it went into reverse the engine was shifting to the right and the mechanical fan was hitting the A/C line, we reattached the clip holding it to the other line and pulling it away from the fan and put a piece of rubber hose over where it had been rubbing. Hoping the hose over the line will buy us some time should we hear the noise again, and spare the cost of a new A/C manifold line.
Last edited by Desert Rat; 07-03-2010 at 07:35 PM.
#6910
Honorary Moderator
Join Date: Mar 2010
Location: Gilbert AZ/Las Cruces NM
Posts: 8,135
Likes: 0
Received 14 Likes
on
12 Posts
Year: 1996
Model: Cherokee
Engine: 4.0 upgraded
drove about 60-70 miles of 6%-7% grades in 110* heat.... never went above 210*-220* even flooring it around 3500 rpms at times
#6911
Senior Member
Join Date: Nov 2008
Location: south bend indiana
Posts: 958
Likes: 0
Received 7 Likes
on
6 Posts
Year: 1993
Model: Cherokee(XJ)
Engine: 4.0 i six H.O.
silicone lubed all my rubber bushings, seen my rear passenger shock might be leaking,oil all over it. made sure i got the right fuel pump locking ring and gasket and it is.
#6912
CF Veteran
Join Date: May 2010
Location: Maryville Tennessee
Posts: 1,626
Likes: 0
Received 1 Like
on
1 Post
Year: 1995
Model: Cherokee
Engine: 4.0 L
Installed a cb today and got these really cool security cable locks for my Hi Lift and spare tire,Bought several of these cables,not sure what to do with the rest
#6913
Seasoned Member
Join Date: Mar 2010
Location: North, Ga
Posts: 388
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Grand Cherokee
Engine: 4.0
Spent 1.5 hours cutting my front bumper off... what a PITA
Then went wheeling for 8 hours on the way home we saw bright flashes in the sky and followed them. Ended up getting to watch some great fireworks.
Then went wheeling for 8 hours on the way home we saw bright flashes in the sky and followed them. Ended up getting to watch some great fireworks.