What did you do to your Cherokee today?
#873
Newbie
Join Date: Nov 2008
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
took a picture to put up on the site after just finding out there was such a bad ***** xj community out there! thank you guys for being there!!!! gramps (my xj) will love it!!!!
#874
Seasoned Member
Join Date: Sep 2008
Posts: 329
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1989
Model: Cherokee
Engine: 4.0
#875
Seasoned Member
Join Date: Jun 2008
Location: Green Bay, WI
Posts: 322
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993 2 door
Model: Cherokee
Engine: 4.0L H.O.
Yes this is the same chevy brushguard.
1.)Had extensions welded onto the framerails out to the bottom of the guard
2.)The headlight loops were shortened 5.5" on each side.
3.)lowered the top part down onto the pull bar more and redrilled the holes. (to drop it vertically some)
1.)Had extensions welded onto the framerails out to the bottom of the guard
2.)The headlight loops were shortened 5.5" on each side.
3.)lowered the top part down onto the pull bar more and redrilled the holes. (to drop it vertically some)
#876
CF Veteran
Join Date: Jan 2008
Location: Puerto Rico
Posts: 1,504
Likes: 0
Received 0 Likes
on
0 Posts
Yes this is the same chevy brushguard.
1.)Had extensions welded onto the framerails out to the bottom of the guard
2.)The headlight loops were shortened 5.5" on each side.
3.)lowered the top part down onto the pull bar more and redrilled the holes. (to drop it vertically some)
1.)Had extensions welded onto the framerails out to the bottom of the guard
2.)The headlight loops were shortened 5.5" on each side.
3.)lowered the top part down onto the pull bar more and redrilled the holes. (to drop it vertically some)
#877
Seasoned Member
Join Date: Jun 2008
Location: Green Bay, WI
Posts: 322
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993 2 door
Model: Cherokee
Engine: 4.0L H.O.
They are attached to the brush guard. They are on a pin, like they swing a little bit.
The welder said that If I didnt like them or if they effected the approach angle too much to just cut them off.
I'll get a better picture.
The welder said that If I didnt like them or if they effected the approach angle too much to just cut them off.
I'll get a better picture.
#878
Today I
Put red 3M reflective 1/4 wide tape along the sides above and below the body crease/ & ran out was 8 in short. so I modyfied my plan with some Suzuki & Kawasaki letters!
#880
Senior Member
Join Date: Oct 2008
Location: Mishawaka, Indiana
Posts: 695
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0L I6
Anyways today i fixed my cupholder dilemma. i bought the 4 pack that u can find at some parts stores and wal mart. I cut the L part off 2 of them and this is what i came out with. I used about 1" screws and sealed them to prevent water seapage, il problly use some undercoating just in caase, Theres plenty of clearance for the screws above the T Case. Drilling into the floor is the last thing i wanted to do but i think its the best spot iv found. And im still working on the sizing of the pics.
Last edited by caddydaddy1027; 11-06-2008 at 11:16 PM.
#883
CF Veteran
Join Date: Jan 2008
Location: Puerto Rico
Posts: 1,504
Likes: 0
Received 0 Likes
on
0 Posts
and the brush guard is attached to the stock bumper only? if so that is a very dangerous point to pull at,, the stock bumper is not strong enough to resist that pulling pressure, I suggest you relocate them.. just my 2cents
#884
Newbie
Join Date: Oct 2008
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1992
Model: Cherokee
Engine: 4.0ho
I went to club meet and scored for free ford d 60 steer linkage!!!!!!! I will be installing it and new bumper this weekend. Also got a pillar triple gauge mout now only if I can find the gauges I put up few months ago! LMAO I'll post pix soon.
#885
Seasoned Member
Join Date: Jun 2008
Location: Green Bay, WI
Posts: 322
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1993 2 door
Model: Cherokee
Engine: 4.0L H.O.
I doubt I will ever pull from it, but it looks/feels strong.