Last edit by: IB Advertising
See related guides and technical advice from our community experts:
Browse all: Wheels and Tires
- Jeep Grand Cherokee ZJ 1993 to 1998 Tires General Information and Specs
Important information to help you understand your Jeep Grand Cherokee.
Browse all: Wheels and Tires
All Lift & Tire questions go here!!!
#4096
Senior Member
Join Date: May 2010
Location: Nevada City, California
Posts: 530
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2K
Model: Cherokee
Engine: I6 with Mustang fuel injectors; 60mm Throttle Body;
#4098
Seasoned Member
Join Date: Apr 2011
Location: Iowa
Posts: 435
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1988
Model: Cherokee
Engine: 4.0
Zone, Rustys or RC
looking at a 3 inch kit AAL my leafs dont sag so i would go this route for now which do you prefer? I have heard alot of good out of all 3 any input or people can post up pics of there 3 inch set up if they would like thanks!
#4100
Junior Member
Join Date: May 2010
Location: Gloucester, Virginia
Posts: 37
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2001
Model: Cherokee
Engine: 4.0L
Stock 2" lift from factory?
hello everyone,
I own a 2001 Cherokee Limited with stock 16" rims and 225/75/16's. I happened to notice that the Jeep sits a tad higher than most other ones I park next to including my girlfriends '98 Classic that stock. So the other day I did some measuring and scoping around under the jeep. I have pucks up top that look like daystar or what-have-you polyurathane coil spacers. I have about 2" more up front that my GF's and about a 1.5" out back higher than my GF's. Any insight, I heard that the '01's came with a factory lift but havn't heard anything rock solid yet. my rear seams to be sagging but I don't want to put anything back there cause I don't want to raise it more, just level. And since im writing this what is the tallest tire i can put on with out rubbing or very slight rubbing with about 2"? I plan on getting some 16" moabs and ATZ pluses again (best tire ever!).
Any help is appreciated.
I own a 2001 Cherokee Limited with stock 16" rims and 225/75/16's. I happened to notice that the Jeep sits a tad higher than most other ones I park next to including my girlfriends '98 Classic that stock. So the other day I did some measuring and scoping around under the jeep. I have pucks up top that look like daystar or what-have-you polyurathane coil spacers. I have about 2" more up front that my GF's and about a 1.5" out back higher than my GF's. Any insight, I heard that the '01's came with a factory lift but havn't heard anything rock solid yet. my rear seams to be sagging but I don't want to put anything back there cause I don't want to raise it more, just level. And since im writing this what is the tallest tire i can put on with out rubbing or very slight rubbing with about 2"? I plan on getting some 16" moabs and ATZ pluses again (best tire ever!).
Any help is appreciated.
#4102
☠ CF Sheriff ☠
Ok I picked up some V8 thunder bird springs for my bastard pack lift I am working on. So the springs are a lot thicker than stock. At the base they are hanging up and I cant get them in at all. can I put a j hook through the hole where the stock spring retainer is or do you think its not safe. The base of the spring is pretty much equally distributed. Only fear I have is could they pop off when flexing? But I bought some of these J bolts and I just not sure if they will hold it in place. I was going to drill a hole at the base and put two J hooks, one I could use the hole from the stock retainer. Do you guys think this is safe?
Or just grind a bit more... (from the jeep - not the spring)
#4103
☠ CF Sheriff ☠
4.5"
Control Arm Length Application Chart
For Jeep Cherokee (XJ)
Lift...........Lower Control Arms/Upper Control Arms
********Decimal**Fraction**Decimal**Fraction
Stock........15.75.......15 ¾........15.00........15
2”.............15.92.......16............14.88.... ...15
3”.............16.09.......16............14.92.... ...15
4”.............16.33.......16 3/8......15.03........15
4.5”..........16.47.......16 ½........15.11........15
5”.............16.62.......16 5/8......15.21........15 ¼
6”.............16.97.......17............15.44.... ...15 ½
7”.............17.36.......17 3/8......15.74........15 ¾
8”.............17.81.......17 ¾........16.09........16
9”.............18.30.......18 ¼........16.50........16 ½
10”...........18.82.......18 ¾........16.96.........17
For Jeep Cherokee (XJ)
Lift...........Lower Control Arms/Upper Control Arms
********Decimal**Fraction**Decimal**Fraction
Stock........15.75.......15 ¾........15.00........15
2”.............15.92.......16............14.88.... ...15
3”.............16.09.......16............14.92.... ...15
4”.............16.33.......16 3/8......15.03........15
4.5”..........16.47.......16 ½........15.11........15
5”.............16.62.......16 5/8......15.21........15 ¼
6”.............16.97.......17............15.44.... ...15 ½
7”.............17.36.......17 3/8......15.74........15 ¾
8”.............17.81.......17 ¾........16.09........16
9”.............18.30.......18 ¼........16.50........16 ½
10”...........18.82.......18 ¾........16.96.........17
#4104
Seasoned Member
Join Date: Jan 2009
Location: Central NJ
Posts: 261
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2000
Model: Cherokee
Engine: 4.0
Im peicing together a 3inch lift, Ive ordered 3 inch leafs with AAL already installed, 3 inch coils, JK shocks, RC brake line extension, 8.25 ubolts and a 1inch T-Case drop. Anything else i need to get this done?
#4109
Senior Member
Join Date: May 2010
Location: Nevada City, California
Posts: 530
Likes: 0
Received 0 Likes
on
0 Posts
Year: 2K
Model: Cherokee
Engine: I6 with Mustang fuel injectors; 60mm Throttle Body;