Motor mounts
#17
Junior Member
Join Date: Jan 2016
Location: Oregon
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1992
Model: Cherokee
Engine: 4.0 HO
I've got my mount set up and ready to go with a problem though: the engine is off kilter - it's leaning to the right.
I'm thinking about trying to start it to see if it'll pop into place (passenger side is not secured, driver's is).
Good or bad idea, since I don't have anything to get it in place right now?
I'm thinking about trying to start it to see if it'll pop into place (passenger side is not secured, driver's is).
Good or bad idea, since I don't have anything to get it in place right now?
#19
Junior Member
Join Date: Jan 2016
Location: Oregon
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1992
Model: Cherokee
Engine: 4.0 HO
Both sides or just the one?
I have the passenger side loose (of course), but not the driver's side.
Should I loosen that one up and give it a go?
Might it pop back in under it's own volition?
Should I loosen that one up and give it a go?
Might it pop back in under it's own volition?
#21
Newbie
Join Date: Oct 2015
Location: Elkhart,In
Posts: 7
Likes: 0
Received 2 Likes
on
1 Post
Year: 2000
Model: Cherokee
Engine: I-6
motor mounts
Did you loosen the tranny mounts???? It is important to loosen them so the motor and tranny come up together and not bind and get everything in a bind. Keep the left side loose also and try again. Once in only snug up the big bolt and then back it off a 1/4 turn. Run it that way for a couple weeks and then you can adjust how smooth it is with the big bolt. The small ones should be 40 lbs.
#22
Newbie
Join Date: Jan 2019
Location: Salinas,CA
Posts: 16
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee (XJ)
Engine: High Output 4.0
I'm running Brown Dog rubber mounts and have zero vibes. Took about 500-600miles for them to break in good.. At first yes there was a slight and I mean slight vibe, but now its great.. The through bolt is not torque specific most ppl over tighten them and get mad vibes. I'm glad I went BD motor mounts.
Here is a vid from my dash cam stuck to windshield with cheap mount(picks up every little pump or vibe).. You can read the lic on the car.. You can see if there was a bad vibe the vid would show it.. Looks smooth on vid and feels good and solid.
Almost Bud - YouTube
Here is a vid from my dash cam stuck to windshield with cheap mount(picks up every little pump or vibe).. You can read the lic on the car.. You can see if there was a bad vibe the vid would show it.. Looks smooth on vid and feels good and solid.
Almost Bud - YouTube
#25
Junior Member
Join Date: Dec 2011
Location: Westminster, CO
Posts: 73
Likes: 0
Received 14 Likes
on
9 Posts
Year: 2001
Model: Cherokee (XJ)
Engine: 4.0l
I tried the Brown Dog "rubber" mounts.
Did not like them at all.
Went back to OEM rubber mounts.
I could never get the Brown Dogs adjusted properly to get rid of the vibration.
Might have just been me, but I carried a wrench around with me for two weeks, making adjustments.
Just my 2 cents!
Did not like them at all.
Went back to OEM rubber mounts.
I could never get the Brown Dogs adjusted properly to get rid of the vibration.
Might have just been me, but I carried a wrench around with me for two weeks, making adjustments.
Just my 2 cents!
#26
CF Veteran
Love my Brown Dog mounts on my 4.0 Wrangler. Yes, do not torque them down. Yes, daily driver.
Last edited by robertj; 02-02-2022 at 12:19 PM.
Thread
Thread Starter
Forum
Replies
Last Post
raminboy
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
17
12-23-2011 01:56 PM
Kyle42
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
6
08-13-2011 11:51 AM
WantACherokee
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
7
01-24-2011 08:15 AM
keith two tone cherokee
Stock XJ Cherokee Tech. All XJ Non-modified/stock questions go here
1
08-28-2009 04:14 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)