What did you do to your Cherokee today?
CF Veteran
Join Date: Dec 2016
Location: SoCal
Posts: 3,493
Received 391 Likes
on
309 Posts
Year: 1987
Model: Cherokee (XJ)
CF Veteran
Join Date: Dec 2016
Location: SoCal
Posts: 3,493
Received 391 Likes
on
309 Posts
Year: 1987
Model: Cherokee (XJ)
Earl, for you, no problem. I know you have been on the hunt for a set anyways. I will pop them out this weekend before the shocks go in the dumpster. PM me your shipping info and I will get them coming.
CF Veteran
Join Date: Dec 2016
Location: SoCal
Posts: 3,493
Received 391 Likes
on
309 Posts
Year: 1987
Model: Cherokee (XJ)
Anytime good sir!
CF Veteran
Join Date: Oct 2013
Location: Greenville, SC
Posts: 5,920
Likes: 0
Received 190 Likes
on
165 Posts
Year: 1999
Model: Cherokee(XJ)
Engine: 4.0
Pulled the pukegoat out of the Comanche and started pulling the engine before the rain came. I think I'm getting pretty quick at this pulling stuff apart thing...
CF Veteran
Join Date: Dec 2016
Location: SoCal
Posts: 3,493
Received 391 Likes
on
309 Posts
Year: 1987
Model: Cherokee (XJ)
Got a couple more bolts left to tighten and then this thing is going down the road!
Edit - Got it back on the ground and took it for a test drive. All is good!
Edit - Got it back on the ground and took it for a test drive. All is good!
Last edited by 5-Speed; 05-25-2018 at 09:29 PM.
CF Veteran
Join Date: Oct 2015
Posts: 7,405
Likes: 0
Received 1,555 Likes
on
1,195 Posts
Year: 2000
Model: Cherokee (XJ)
OK so what I did with my XJ today. Went and picked up this tool box. $100 off of Offer Up. Nothing fancy. Not roller bearing drawers. They slide nice and the box is in decent shape. Also got some tools with it. Everything below the face mask and left of the clamp are Snap On's or Blue Points. Anybody have any idea what the tool is between the speed wrench and punches. Last shot is just more crap that was in the box.
Senior Member
Ralph - That looks like a spreader for your battery clamps. When you take them off you sometimes need to spread them a bit to get them back on.
CF Veteran
Join Date: Oct 2015
Posts: 7,405
Likes: 0
Received 1,555 Likes
on
1,195 Posts
Year: 2000
Model: Cherokee (XJ)
CF Veteran
Join Date: Oct 2013
Location: Greenville, SC
Posts: 5,920
Likes: 0
Received 190 Likes
on
165 Posts
Year: 1999
Model: Cherokee(XJ)
Engine: 4.0
Went to the junkyard and pulled a head, intake, power steering pump, and power steering pump bracket, and then went home and pulled the intake, exhaust and head off the Comanche. Taking a break and then hopefully pulling the block in a little. yes that pushrod has been sitting there, no I didn't move it. It's been running with it just sitting there for a few thousand miles apparently. Not bent either. cylinder head is nasty and finally the block.
CF Veteran
Join Date: May 2013
Location: Asheville, NC
Posts: 2,569
Received 253 Likes
on
170 Posts
Year: 1999
Engine: 4.0
Are you going to do anything to block except maybe clean it? "Dingle ball" hone?
Installed some Custom4x4 Fabrication tow hooks today. I really like how they were made and the install was easy.
I now have front and rear recovery points - it's starting to look like a Jeep too.
Installed some Custom4x4 Fabrication tow hooks today. I really like how they were made and the install was easy.
I now have front and rear recovery points - it's starting to look like a Jeep too.
Last edited by Battle; 05-26-2018 at 07:32 PM.