Event
By
Thread/Post
Forum
New Post
By: ijeeep
Today 01:08 AM
Steel and aluminum aren't a good mix without special treatments and coatings. Galvanic corrosion is a thing. There's books and charts on the subject. Bronzes and maybe Delrin and Nylon 6-6...
(110 views, 1 replies)
New Post
By: Comanche SS
Yesterday 11:20 PM
Little sneak peak of what's coming up for this build https://cimg6.ibsrv.net/gimg/www.cherokeeforum.co m-vbulletin/2000x926/20240501_200957_ab97 46c5d10b14bd153cb019 7c28d07813a023a3.jpg
(1,384 views, 14 replies)
New Post
By: 94zj318
Yesterday 11:00 PM
It's usually a blue wire in the aftermarket radio's wiring harness. Although the Boston Acoustics amplifier is a digital amplifier, so it uses a digital signal from the radio. You should still...
(5,461 views, 3 replies)
New Post
By: Roler
Yesterday 09:39 PM
There is a bit of info in threads on the forum. Do you have AC? Does the fan come on when you select an AC setting? At the fan relay, jump the 30 and 78 'recepticles' for the same number pins ....
(151 views, 1 replies)
New Post
By: IJM
Yesterday 09:06 PM
My guess is something wrong with the selector switch. Otherwise, all MAX does is switch to recirculated air.
(248 views, 1 replies)
New Post
By: Dibbons
Yesterday 08:28 PM
Update: Removed the valve cover which inside was "clean" but pitch black in color. The cylinder head surface also appears "clean" but is also pitch black in color. I found the casting number 0331....
(806 views, 9 replies)
New Post
By: chilidipper
Yesterday 07:11 PM
Yes, angle is good today. Good extended shackles. If i change the height this opens a can worms. Shocks, coils and other geometries
(159 views, 4 replies)
New Thread
By: mgray9119
Yesterday 07:00 PM
I got my 1998 Jeep Cherokee repainted. The job is good, but they did not put the car back together well. In addition to multiple other problems, they lost one of the screws that attaches the door...
(170 views, 0 replies)
New Thread
Yesterday 06:30 PM
Hello all I have a 99 xj and it has a 4 in lift and I am running 32s right now. A little small for the lift but it works. The main problem is that it has pocket flares which look not great imo. I...
(59 views, 0 replies)
New Post
By: ijeeep
Yesterday 06:20 PM
Swap in used rear end. Rebuild original at your convenience. Enjoy lower total lifecycle cost.
(174 views, 2 replies)
New Post
By: Yimtoung
Yesterday 05:00 PM
This all started in March of 2023. Running now! I replaced the crank shaft sensor and cam position sensor twice. The throttle sensor once. Was able to get an electrical schematic for the vehicle and...
(618 views, 8 replies)
New Post
By: Saudade
Yesterday 03:47 PM
Right, the small diameter one is a vacuum hose. Not sure where it goes but one end will be on the intake manifold. The other end maybe to the fuel pressure regulator? The big line is likely an...
(220 views, 1 replies)
New Post
By: 00t444e
Yesterday 02:07 PM
Stock steering box is fine but you should get a Hydro assist kit for running tires that big.
(346 views, 6 replies)
New Post
Yesterday 01:50 PM
Howdy, Do you still have both sets of grilles / headlight bezels? Thanks!
(462 views, 1 replies)
New Post
By: RockyMtn96XJ
Yesterday 01:37 PM
Oh I've got plenty of anti-seize hahaha... a large bottle and brush. I just wasnt sure if there was a more complex answer than just slapping some on there and calling it a day. But if its that...
(89 views, 2 replies)
New Post
Yesterday 01:31 PM
https://cimg4.ibsrv.net/gimg/www.cherokeeforum.co m-vbulletin/1080x1920/snapchat_2000613577_ 1c5baf923aa5fee86050 defd1cf5a499321685a3 .jpg 93 grand cherokee limited 5.2 in progress traded my go kart...
(853,962 views, 403 replies)
New Post
By: cannothas
Yesterday 01:07 PM
This past weekend I chopped my fenders off to make room for 31x10.50's. Looks good from far, just don't feel the cuts, they're not perfect 😏...
(8,122,115 views, 95,241 replies)